X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2Fxtfpga.h;h=516a6089f6d8d668e499b279b56268acd3b41ce8;hb=406df85345f942d9348443983d81a01e013e920b;hp=c7862be10d72214681a4bc7294da8f0cb07b0385;hpb=5ebd27d860ec0c6e36f1b0f973653fe66a7360be;p=oweals%2Fu-boot.git

diff --git a/include/configs/xtfpga.h b/include/configs/xtfpga.h
index c7862be10d..516a6089f6 100644
--- a/include/configs/xtfpga.h
+++ b/include/configs/xtfpga.h
@@ -1,8 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright (C) 2007-2013 Tensilica, Inc.
  * Copyright (C) 2014 - 2016 Cadence Design Systems Inc.
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -66,15 +65,12 @@
 # define CONFIG_SYS_MONITOR_LEN		0x00040000	/* 256KB */
 #endif
 
-#define CONFIG_SYS_STACKSIZE		(512 << 10)	/* stack 512KB */
 #define CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* heap  256KB */
 
 /* Linux boot param area in RAM (used only when booting linux) */
 #define CONFIG_SYS_BOOTPARAMS_LEN	(64  << 10)
 
 /* Memory test is destructive so default must not overlap vectors or U-Boot*/
-#define CONFIG_SYS_MEMTEST_START	MEMADDR(0x01000000)
-#define CONFIG_SYS_MEMTEST_END		MEMADDR(0x02000000)
 
 /* Load address for stand-alone applications.
  * MEMADDR cannot be used here, because the definition needs to be
@@ -99,9 +95,8 @@
 #define CONFIG_SYS_MEMORY_SIZE		CONFIG_SYS_SDRAM_SIZE
 #endif
 
-#define CONFIG_SYS_MEMORY_TOP		MEMADDR(CONFIG_SYS_MEMORY_SIZE)
-#define CONFIG_SYS_TEXT_ADDR		\
-	(CONFIG_SYS_MEMORY_TOP - CONFIG_SYS_MONITOR_LEN)
+#define XTENSA_SYS_TEXT_ADDR		\
+	(MEMADDR(CONFIG_SYS_MEMORY_SIZE) - CONFIG_SYS_MONITOR_LEN)
 
 /* Used by tftpboot; env var 'loadaddr' */
 #define CONFIG_SYS_LOAD_ADDR		MEMADDR(0x02000000)
@@ -110,45 +105,18 @@
 /* U-Boot general configuration */
 /*==============================*/
 
-#undef	CONFIG_USE_IRQ			/* Keep it simple, poll only */
 #define CONFIG_BOARD_POSTCLK_INIT
-#define CONFIG_MISC_INIT_R
 
 #define CONFIG_BOOTFILE			"uImage"
 	/* Console I/O Buffer Size  */
 #define CONFIG_SYS_CBSIZE		1024
-	/* Prt buf */
-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
-					 sizeof(CONFIG_SYS_PROMPT) + 16)
-	/* max number of command args */
-#define CONFIG_SYS_MAXARGS		16
 	/* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
 
-/*=================*/
-/* U-Boot commands */
-/*=================*/
-
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_SAVES
-
 /*==============================*/
 /* U-Boot autoboot configuration */
 /*==============================*/
 
-#define CONFIG_BOOT_RETRY_TIME		60	/* retry after 60 secs */
-
-#define CONFIG_AUTO_COMPLETE			/* Support tab autocompletion */
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-#define CONFIG_SHOW_BOOT_PROGRESS
-
-#ifdef DEBUG
-#define CONFIG_PANIC_HANG		1	/* Require manual reboot */
-#endif
-
 
 /*=========================================*/
 /* FPGA Registers (board info and control) */
@@ -207,8 +175,6 @@
 
 /* Input clk to NS16550 (in Hz; the SYS_CLK_FREQ is in kHz) */
 #define CONFIG_SYS_NS16550_CLK		CONFIG_SYS_CLK_FREQ
-#define CONFIG_CONS_INDEX		1	/* use UART0 for console */
-#define CONFIG_BAUDRATE			115200	/* Default baud rate */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
 /*======================*/
@@ -223,8 +189,6 @@
 /* Flash & Environment */
 /*=====================*/
 
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER			/* use generic CFI driver */
 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
 #define CONFIG_SYS_MAX_FLASH_BANKS	1
 #ifdef CONFIG_XTFPGA_LX60
@@ -249,15 +213,11 @@
 #define CONFIG_SYS_MAX_FLASH_SECT	\
 	(CONFIG_SYS_FLASH_SECT_SZ/CONFIG_SYS_FLASH_PARMSECT_SZ + \
 	 CONFIG_SYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ - 1)
-#define CONFIG_SYS_FLASH_PROTECTION		/* hw flash protection */
 
 /*
  * Put environment in top block (64kB)
  * Another option would be to put env. in 2nd param block offs 8KB, size 8KB
  */
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_OFFSET    (CONFIG_SYS_FLASH_SIZE - CONFIG_SYS_FLASH_SECT_SZ)
-#define CONFIG_ENV_SIZE	     CONFIG_SYS_FLASH_SECT_SZ
 
 /* print 'E' for empty sector on flinfo */
 #define CONFIG_SYS_FLASH_EMPTY_INFO