X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2Fxm250.h;h=32544fed5801610ca26f88ef9c13d9f9ecc7de2b;hb=7899147b5577c1b701e320ebb792e3579e7302e5;hp=2ff9a2813adc9f4e25ecb656ce97531b30416c60;hpb=37a3bda0c9c8a2ffbf7e2a9e121177a3385a0626;p=oweals%2Fu-boot.git

diff --git a/include/configs/xm250.h b/include/configs/xm250.h
index 2ff9a2813a..32544fed58 100644
--- a/include/configs/xm250.h
+++ b/include/configs/xm250.h
@@ -35,9 +35,10 @@
 #define CONFIG_PXA250	       1	/* This is an PXA250 CPU	*/
 #define CONFIG_XM250	       1	/* on a MicroSys XM250 Board	*/
 #undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff	*/
+#define	CONFIG_SYS_TEXT_BASE	0x0
 
 /* we will never enable dcache, because we have to setup MMU first */
-#define CONFIG_SYS_NO_DCACHE
+#define CONFIG_SYS_DCACHE_OFF
 
 /*
  * Size of malloc() pool; this lives below the uppermost 128 KiB which are
@@ -45,7 +46,6 @@
  *
  */
 #define CONFIG_SYS_MALLOC_LEN		(256*1024)
-#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
 
 /*
  * Hardware drivers
@@ -61,6 +61,8 @@
 /*
  * I2C bus
  */
+#define CONFIG_I2C_MV			1
+#define CONFIG_MV_I2C_REG		0x40301680
 #define CONFIG_HARD_I2C			1
 #define CONFIG_SYS_I2C_SPEED			50000
 #define CONFIG_SYS_I2C_SLAVE			0xfe
@@ -137,7 +139,6 @@
 #define CONFIG_CMDLINE_TAG	 1	 /* send commandline to Kernel		*/
 #define CONFIG_SETUP_MEMORY_TAGS 1	 /* send memory definition to kernel	*/
 #define	CONFIG_INITRD_TAG	 1	 /* do not send initrd params		*/
-#undef	CONFIG_VFD			 /* do not send framebuffer setup	*/
 
 /*
  * Stack sizes
@@ -175,7 +176,7 @@
 #define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
 
 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
-#define	CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_GBL_DATA_SIZE + PHYS_SDRAM_1)
+#define	CONFIG_SYS_INIT_SP_ADDR		(GENERATED_GBL_DATA_SIZE + PHYS_SDRAM_1)
 
 /*
  * FLASH and environment organization
@@ -322,9 +323,9 @@
  * Clocks, power control and interrupts
  */
 #define CONFIG_SYS_PSSR_VAL	    0x00000030
-#define CONFIG_SYS_CCCR_VAL	    0x00000161	/* 100 MHz memory, 400 MHz CPU, 400 Turbo  */
-#define CONFIG_SYS_CKEN_VAL	    0x000141ec	/* FFUART and STUART enabled	*/
-#define CONFIG_SYS_ICMR_VAL	    0x00000000	/* No interrupts enabled	*/
+#define CONFIG_SYS_CCCR		    0x00000161	/* 100 MHz memory, 400 MHz CPU, 400 Turbo  */
+#define CONFIG_SYS_CKEN		    0x000141ec	/* FFUART and STUART enabled	*/
+#define CONFIG_SYS_ICMR		    0x00000000	/* No interrupts enabled	*/
 
 /* FIXME
  *
@@ -343,6 +344,8 @@
 #define CONFIG_SYS_MDCNFG_VAL	    0x000009c9
 #define CONFIG_SYS_MDMRS_VAL	    0x00220022
 #define CONFIG_SYS_MDREFR_VAL	    0x000da018	/* Initial setting, individual bits set in lowlevel_init.S */
+#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
+#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
 
 /*
  * PCMCIA and CF Interfaces (NOT USED, these values from lubbock init)