X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2Fsbc8548.h;h=617be273ec20906633c56045f0480bd0c386c489;hb=b05c344809ef45be7a5df9b6f4cc694551b0d66e;hp=84be5246b91c270bf0157a962089e986cb626443;hpb=3be2bdf5dc69b3142c1162a59bc67191c9077567;p=oweals%2Fu-boot.git

diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index 84be5246b9..617be273ec 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -38,8 +38,6 @@
  */
 #define CONFIG_BOOKE		1	/* BOOKE */
 #define CONFIG_E500		1	/* BOOKE e500 family */
-#define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48 */
-#define CONFIG_MPC8548		1	/* MPC8548 specific */
 #define CONFIG_SBC8548		1	/* SBC8548 board specific */
 
 /*
@@ -71,8 +69,6 @@
 
 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
 
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
-
 /*
  * Below assumes that CCB:SYSCLK remains unchanged at 6:1 via SW2:[1-4]
  */
@@ -102,7 +98,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #undef CONFIG_DDR_ECC			/* only for ECC DDR module */
 /*
@@ -406,7 +402,6 @@
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX	1
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		(400000000 / CONFIG_SYS_CLK_DIV)
@@ -417,14 +412,6 @@
 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
-
 /*
  * I2C
  */
@@ -471,9 +458,6 @@
 #endif
 
 #if defined(CONFIG_PCI)
-
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
@@ -481,7 +465,6 @@
 
 #endif	/* CONFIG_PCI */
 
-
 #if defined(CONFIG_TSEC_ENET)
 
 #define CONFIG_MII		1	/* MII PHY management */
@@ -531,23 +514,15 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
 #endif
 
-
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
 
 /*
@@ -557,7 +532,6 @@
 #define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
@@ -566,7 +540,6 @@
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
@@ -577,19 +550,14 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 
 /*
  * Environment Configuration
  */
-
-/* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_HAS_ETH0
-#define CONFIG_ETHADDR	 02:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR	 02:E0:0C:00:01:FD
 #endif
 
 #define CONFIG_IPADDR	 192.168.0.55
@@ -605,7 +573,6 @@
 
 #define CONFIG_LOADADDR	1000000	/*default location for tftp and bootm*/
 
-#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
 #undef	CONFIG_BOOTARGS		/* the boot command will set bootargs*/
 
 #define CONFIG_BAUDRATE	115200
@@ -622,7 +589,7 @@
 "consoledev=ttyS0\0"				\
 "ramdiskaddr=2000000\0"			\
 "ramdiskfile=uRamdisk\0"			\
-"fdtaddr=c00000\0"				\
+"fdtaddr=1e00000\0"				\
 "fdtfile=sbc8548.dtb\0"
 
 #define CONFIG_NFSBOOTCOMMAND						\
@@ -634,7 +601,6 @@
    "tftp $fdtaddr $fdtfile;"						\
    "bootm $loadaddr - $fdtaddr"
 
-
 #define CONFIG_RAMBOOTCOMMAND \
    "setenv bootargs root=/dev/ram rw "					\
       "console=$consoledev,$baudrate $othbootargs;"			\