X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2Fmx6qsabreauto.h;h=22603442d73f79903434584f7c68e7129585c3b1;hb=f8cb101e1e3f5ee2007b78b6b12e24120385aeac;hp=f4a082aeaaa3f773c5b6d6374dd90f02a05fa594;hpb=a17617d6553369ba72c080128ed8d0b0c33dfc89;p=oweals%2Fu-boot.git

diff --git a/include/configs/mx6qsabreauto.h b/include/configs/mx6qsabreauto.h
index f4a082aeaa..22603442d7 100644
--- a/include/configs/mx6qsabreauto.h
+++ b/include/configs/mx6qsabreauto.h
@@ -3,10 +3,7 @@
  *
  * Configuration settings for the Freescale i.MX6Q SabreAuto board.
  *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
+ * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #ifndef __MX6QSABREAUTO_CONFIG_H
@@ -15,15 +12,73 @@
 #define CONFIG_MACH_TYPE	3529
 #define CONFIG_MXC_UART_BASE	UART4_BASE
 #define CONFIG_CONSOLE_DEV		"ttymxc3"
+#if defined CONFIG_MX6Q
 #define CONFIG_DEFAULT_FDT_FILE	"imx6q-sabreauto.dtb"
+#elif defined CONFIG_MX6DL
+#define CONFIG_DEFAULT_FDT_FILE	"imx6dl-sabreauto.dtb"
+#endif
 #define CONFIG_MMCROOT			"/dev/mmcblk0p2"
 #define PHYS_SDRAM_SIZE		(2u * 1024 * 1024 * 1024)
 
-#include "mx6qsabre_common.h"
+/* USB Configs */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */
+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS	0
+
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_WIDTH	{ {0x30, 8}, {0x32, 8}, {0x34, 8} }
+
+#include "mx6sabre_common.h"
+
+#undef CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
+#define CONFIG_SYS_FLASH_SECT_SIZE      (128 * 1024)
+#define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256   /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER         /* Use drivers/cfi_flash.c */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
+#define CONFIG_SYS_FLASH_EMPTY_INFO
 
 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #if defined(CONFIG_ENV_IS_IN_MMC)
 #define CONFIG_SYS_MMC_ENV_DEV		0
 #endif
 
+/* I2C Configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* NAND flash command */
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
+
+/* NAND stuff */
+#define CONFIG_NAND_MXS
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define CONFIG_SYS_NAND_BASE           0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
+
 #endif                         /* __MX6QSABREAUTO_CONFIG_H */