X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2Fluan.h;h=e192d06923361f108e11e8257170635f6ad6f8f1;hb=2a49fc17d09020e7ebd9536694d99d20e419fcb8;hp=0335a0098585f67898666311e88c6d2bf111e72f;hpb=038ccac511214b062c56f22b9413f784b86bcd87;p=oweals%2Fu-boot.git

diff --git a/include/configs/luan.h b/include/configs/luan.h
index 0335a00985..e192d06923 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -37,8 +37,9 @@
 #define CONFIG_440		1
 #define CONFIG_SYS_CLK_FREQ	33333333 /* external freq to pll	*/
 
-#define CONFIG_BOARD_EARLY_INIT_F 1     /* call board_early_init_f()	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
+#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
@@ -132,10 +133,9 @@
 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
-#undef  CONFIG_SPD_EEPROM		/* SPD EEPROM init doesn't support DDR2 */
-#define SPD_EEPROM_ADDRESS {0x52,0x53}	/* I2C SPD addresses */
-#define IIC0_DIMM0_ADDR         0x52
-#define IIC0_DIMM1_ADDR         0x53
+#define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for setup	*/
+#define SPD_EEPROM_ADDRESS	{0x53, 0x52}	/* SPD i2c spd addresses*/
+#define CONFIG_DDR_ECC		1	/* with ECC support		*/
 
 /*-----------------------------------------------------------------------
  * I2C
@@ -145,6 +145,13 @@
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CFG_I2C_SLAVE		0x7F
 
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
 	"echo"
@@ -171,6 +178,7 @@
 	"bootfile=/tftpboot/luan/uImage\0"				\
 	"kernel_addr=fc000000\0"					\
 	"ramdisk_addr=fc100000\0"					\
+	"initrd_high=30000000\0"					\
 	"load=tftp 100000 /tftpboot/luan/u-boot.bin\0"			\
 	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
 		"cp.b 100000 fffc0000 40000;"			        \
@@ -198,11 +206,6 @@
 #define CONFIG_NETCONSOLE		/* include NetConsole support	*/
 #define CONFIG_NET_MULTI		/* needed for NetConsole	*/
 
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
 #ifdef DEBUG
 #define CONFIG_PANIC_HANG
 #else
@@ -211,10 +214,9 @@
 
 #define CONFIG_COMMANDS	       (CONFIG_CMD_DFL		|	\
 				CFG_CMD_ASKENV		|	\
-			        CFG_CMD_CACHE		|	\
 				CFG_CMD_DHCP		|	\
-				CFG_CMD_DIAG		|	\
 				CFG_CMD_ELF		|	\
+				CFG_CMD_EEPROM		|	\
 				CFG_CMD_I2C		|	\
 				CFG_CMD_IRQ		|	\
 				CFG_CMD_MII		|	\
@@ -223,7 +225,6 @@
 				CFG_CMD_PCI		|	\
 				CFG_CMD_PING		|	\
 				CFG_CMD_REGINFO		|	\
-				CFG_CMD_SETGETDCR	|	\
 				CFG_CMD_SDRAM		|	\
 				0)
 
@@ -253,6 +254,12 @@
 
 #define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks */
 
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
@@ -265,7 +272,6 @@
 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup  */
 
 /* Board-specific PCI */
-#define CFG_PCI_PRE_INIT                /* enable board pci_pre_init()  */
 #define CFG_PCI_TARGET_INIT
 #undef  CFG_PCI_MASTER_INIT