X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2Fkorat.h;h=55ef4f033707bd338c46a0308c7150e01805a0e2;hb=d6288664743cdd4824cb877ca424619c827c1256;hp=eb2c1d43b4996799e9e8191067558990b639bb67;hpb=156feb90d200f186cdfd856d7f6f1878bb1bec1e;p=oweals%2Fu-boot.git

diff --git a/include/configs/korat.h b/include/configs/korat.h
index eb2c1d43b4..55ef4f0337 100644
--- a/include/configs/korat.h
+++ b/include/configs/korat.h
@@ -69,9 +69,7 @@
 #define CONFIG_SYS_OCM_DATA_ADDR	CONFIG_SYS_OCM_BASE
 #define CONFIG_SYS_PCI_BASE		0xe0000000	/* Internal PCI regs	*/
 #define CONFIG_SYS_PCI_MEMBASE		0x80000000	/* mapped pci memory	*/
-
-/* Don't change either of these */
-#define CONFIG_SYS_PERIPHERAL_BASE	0xef600000	/* internal peripherals	*/
+#define CONFIG_SYS_PCI_MEMBASE2		(CONFIG_SYS_PCI_MEMBASE + 0x20000000)
 
 #define CONFIG_SYS_USB2D0_BASE		0xe0000100
 #define CONFIG_SYS_USB_DEVICE		0xe0000000
@@ -87,16 +85,19 @@
 #define CONFIG_SYS_INIT_RAM_END	(4 << 10)
 #define CONFIG_SYS_GBL_DATA_SIZE	256	/* num bytes initial data	*/
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_POST_WORD_ADDR
+#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
 
 /*
  * Serial Port
  */
+#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
 #define CONFIG_SYS_EXT_SERIAL_CLOCK	11059200	/* ext. 11.059MHz clk	*/
 #define CONFIG_BAUDRATE		115200
 #define CONFIG_SERIAL_MULTI	1
-/* define this if you want console on UART1 */
-#undef CONFIG_UART1_CONSOLE
 
 #define CONFIG_SYS_BAUDRATE_TABLE						\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
@@ -152,6 +153,7 @@
  */
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
@@ -282,7 +284,6 @@
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_I2C
-#define CONFIG_I2C_CMD_TREE
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NET
@@ -305,7 +306,6 @@
 				 CONFIG_SYS_POST_SPR	| \
 				 CONFIG_SYS_POST_UART)
 
-#define CONFIG_SYS_POST_WORD_ADDR	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
 #define CONFIG_LOGBUFFER
 #define CONFIG_SYS_POST_CACHE_ADDR	0xC8000000	/* free virtual address     */
 
@@ -360,6 +360,7 @@
 /* Board-specific PCI */
 #define CONFIG_SYS_PCI_TARGET_INIT
 #define CONFIG_SYS_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ
 
 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC				*/
 #define CONFIG_SYS_PCI_SUBSYS_ID       0xcafe	/* Whatever			*/