X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2Fcobra5272.h;h=c859616c68cb344273fcb58eb0afa2b861299836;hb=08649c3d50b1ca014a9e0bf87c724f99f88a20ce;hp=11dd4d712be372533e64fb2f008e7d3063b97f0e;hpb=3238639d40732fe78fd62ae5e080465552e882fc;p=oweals%2Fu-boot.git

diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h
index 11dd4d712b..c859616c68 100644
--- a/include/configs/cobra5272.h
+++ b/include/configs/cobra5272.h
@@ -1,13 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Configuation settings for the Sentec Cobra Board.
  *
  * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
  */
 
 /* ---
- * Version: U-boot 1.0.0 - initial release for Sentec COBRA5272 board
+ * Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board
  * Date: 2004-03-29
  * Author: Florian Schlote
  *
@@ -33,12 +32,6 @@
 #define CONFIG_SYS_CLK			66000000
 #define CONFIG_SYS_SDRAM_SIZE		16		/* SDRAM size in MB */
 
-/* ---
- * Enable use of Ethernet
- * ---
- */
-#define CONFIG_MCFFEC
-
 /* Enable Dma Timer */
 #define CONFIG_MCFTMR
 
@@ -52,7 +45,6 @@
 
 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		(0)
-#define CONFIG_BAUDRATE		19200
 
 /* ---
  * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
@@ -94,50 +86,20 @@
  * ---
  */
 
-#ifndef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_ENV_OFFSET		0x4000
-#define CONFIG_ENV_SECT_SIZE	0x2000
-#define CONFIG_ENV_IS_IN_FLASH	1
-#else
-#define CONFIG_ENV_ADDR		0xffe04000
-#define CONFIG_ENV_SECT_SIZE	0x2000
-#define CONFIG_ENV_IS_IN_FLASH	1
-#endif
-
 #define LDS_BOARD_TEXT \
-        . = DEFINED(env_offset) ? env_offset : .; \
-        common/env_embedded.o (.text);
+	. = DEFINED(env_offset) ? env_offset : .; \
+	env/embedded.o(.text);
 
 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_LOADB
-#undef CONFIG_CMD_MII
 
 #ifdef CONFIG_MCFFEC
-#	define CONFIG_MII		1
 #	define CONFIG_MII_INIT		1
 #	define CONFIG_SYS_DISCOVER_PHY
 #	define CONFIG_SYS_RX_ETH_BUFFER	8
 #	define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-
-#	define CONFIG_SYS_FEC0_PINMUX		0
-#	define CONFIG_SYS_FEC0_MIIBASE		CONFIG_SYS_FEC0_IOBASE
-#	define MCFFEC_TOUT_LOOP		50000
 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
 #	ifndef CONFIG_SYS_DISCOVER_PHY
 #		define FECDUPLEX	FULL
@@ -157,12 +119,6 @@
 
 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/
 
-#define CONFIG_BOOTDELAY	5		/* used for autoboot, delay in
-seconds u-boot will wait before starting defined (auto-)boot command, setting
-to -1 disables delay, setting to 0 will too prevent access to u-boot command
-interface: u-boot then has to reflashed */
-
-
 /* The following settings will be contained in the environment block ; if you
 want to use a neutral environment all those settings can be manually set in
 u-boot: 'set' command */
@@ -172,9 +128,6 @@ u-boot: 'set' command */
 #define CONFIG_BOOTCOMMAND	"bootm 0xffe80000"	/*Autoboto command, please
 enter a valid image address in flash */
 
-#define CONFIG_BOOTARGS		" "			/* default bootargs that are
-considered during boot */
-
 /* User network settings */
 
 #define CONFIG_IPADDR 192.168.100.2		/* default board IP address */
@@ -182,24 +135,11 @@ considered during boot */
 
 #endif
 
-#define CONFIG_SYS_PROMPT		"COBRA > "	/* Layout of u-boot prompt*/
-
 #define CONFIG_SYS_LOAD_ADDR		0x20000		/*Defines default RAM address
 from which user programs will be started */
 
 /*---*/
 
-#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
 /*
  *-----------------------------------------------------------------------------
  * End of user parameters to be customized
@@ -211,9 +151,6 @@ from which user programs will be started */
  * ---
  */
 
-#define CONFIG_SYS_MEMTEST_START	0x400
-#define CONFIG_SYS_MEMTEST_END		0x380000
-
 /* ---
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)