X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2Fcm_t35.h;h=9767512a5cf03771a5008932433b417cdacfbe56;hb=9637c4b2dd5e84418f7367e5361ba9ff6726e377;hp=7729a02ab658858577a18f5e4a4b097df36b1866;hpb=7f673c99c2d8d1aa21996c5b914f06d784b080ca;p=oweals%2Fu-boot.git

diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
index 7729a02ab6..9767512a5c 100644
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@@ -21,11 +21,11 @@
  * High Level Configuration Options
  */
 #define CONFIG_OMAP	/* in a TI OMAP core */
-#define CONFIG_OMAP34XX	/* which is a 34XX */
 #define CONFIG_OMAP_GPIO
 #define CONFIG_CMD_GPIO
 #define CONFIG_CM_T3X	/* working with CM-T35 and CM-T3730 */
 #define CONFIG_OMAP_COMMON
+#define CONFIG_SYS_GENERIC_BOARD
 
 #define CONFIG_SDRC	/* The chip has SDRC controller */
 
@@ -45,13 +45,6 @@
 #define CONFIG_MISC_INIT_R
 
 #define CONFIG_OF_LIBFDT		1
-/*
- * The early kernel mapping on ARM currently only maps from the base of DRAM
- * to the end of the kernel image.  The kernel is loaded at DRAM base + 0x8000.
- * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000,
- * so that leaves DRAM base to DRAM base + 0x4000 available.
- */
-#define CONFIG_SYS_BOOTMAPSZ	        0x4000
 
 #define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS
@@ -111,8 +104,6 @@
 #define CONFIG_USB_DEVICE
 #define CONFIG_USB_TTY
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
-/* This delay is really for slow-to-power-on USB sticks, not the hub */
-#define CONFIG_USB_HUB_MIN_POWER_ON_DELAY 500
 
 /* commands to include */
 #include <config_cmd_default.h>
@@ -145,6 +136,7 @@
 #define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+#define CONFIG_SYS_I2C_EEPROM_BUS	0
 #define CONFIG_I2C_MULTI_BUS
 
 /*
@@ -163,10 +155,9 @@
 #define CONFIG_SYS_NAND_BASE		NAND_BASE	/* physical address */
 							/* to access nand at */
 							/* CS0 */
-#define GPMC_NAND_ECC_LP_x8_LAYOUT
-
 #define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of NAND */
 							/* devices */
+
 /* Environment information */
 #define CONFIG_BOOTDELAY		3
 #define CONFIG_ZERO_BOOTDELAY_CHECK
@@ -268,9 +259,6 @@
  */
 
 /* **** PISMO SUPPORT *** */
-/* Configure the PISMO */
-#define PISMO1_NAND_SIZE		GPMC_SIZE_128M
-
 /* Monitor at start of flash */
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */
@@ -329,14 +317,13 @@
 #define CONFIG_OMAP3_SPI
 
 /* Defines for SPL */
-#define CONFIG_SPL
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_NAND_SIMPLE
 
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300 /* address 0x60000 */
 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x200 /* 256 KB */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION	1
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME	"u-boot.img"
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"u-boot.img"
 
 #define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_LIBCOMMON_SUPPORT