X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2Faria.h;h=3612e037b9fcb9f05610c30a3ce57544bbdefda5;hb=5b8e76c35ec312a3f73126bd1a2d2c0965b98a9f;hp=ec13b584a6a1fa0c266c98bd761e0f9e59c122b3;hpb=bdba2b3a8809501b7073c242f9aa013eb456790d;p=oweals%2Fu-boot.git

diff --git a/include/configs/aria.h b/include/configs/aria.h
index ec13b584a6..3612e037b9 100644
--- a/include/configs/aria.h
+++ b/include/configs/aria.h
@@ -38,10 +38,6 @@
 
 /* video */
 
-#if defined(CONFIG_VIDEO)
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#endif
-
 /* CONFIG_PCI is defined at config time */
 
 #define CONFIG_SYS_MPC512X_CLKIN	33000000	/* in Hz */
@@ -313,7 +309,6 @@
 #error CONFIG_PSC_CONSOLE must be 3
 #endif
 
-#define CONFIG_BAUDRATE			115200	/* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
@@ -341,37 +336,15 @@
 #define CONFIG_SYS_PCI_IO_PHYS		0x84000000
 #define CONFIG_SYS_PCI_IO_SIZE		0x01000000	/* 16M */
 
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 
 #endif
 
-/* I2C */
-#define CONFIG_HARD_I2C			/* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#if 0
-#define CONFIG_SYS_I2C_NOPROBES	{{0,0x69}}	/* Don't probe these addrs */
-#endif
-
 /*
  * IIM - IC Identification Module
  */
 #undef CONFIG_FSL_IIM
 
-/*
- * EEPROM configuration for Atmel AT24C32A-10TQ-2.7:
- * 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5
-
 /*
  * Ethernet configuration
  */
@@ -399,22 +372,12 @@
 #define CONFIG_LOADS_ECHO		1
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1
 
-#define CONFIG_CMD_EEPROM
-#undef CONFIG_CMD_FUSE
-#undef CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
 #define CONFIG_CMD_PCI
 #endif
 
-#if defined(CONFIG_CMD_IDE) || defined(CONFIG_CMD_EXT2)
-#define CONFIG_DOS_PARTITION
-#define CONFIG_MAC_PARTITION
-#define CONFIG_ISO_PARTITION
-#endif /* defined(CONFIG_CMD_IDE) */
-
 /*
  * Dynamic MTD partition support
  */
@@ -509,8 +472,6 @@
 
 #undef  CONFIG_BOOTARGS			/* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE		115200
-
 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"
@@ -571,8 +532,6 @@
  *-----------------------------------------------------------------------
  */
 
-#undef  CONFIG_IDE_8xx_PCCARD		/* Use IDE with PC Card	Adapter	*/
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
 #undef	CONFIG_IDE_LED			/* LED   for IDE not supported	*/
 
 #define CONFIG_IDE_RESET		/* reset for IDE supported	*/