X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2Fads5121.h;h=f516c4602c2c396e0cb1a0562b054cf451bdd9b8;hb=a55d074dac24dc941f1afb5b4e94b1509bfdda4e;hp=09c31403609c5afb4275df155030ee3a99ab9314;hpb=c62776be8dca4097ca03d4f9415f08d4887b45d0;p=oweals%2Fu-boot.git

diff --git a/include/configs/ads5121.h b/include/configs/ads5121.h
index 09c3140360..f516c4602c 100644
--- a/include/configs/ads5121.h
+++ b/include/configs/ads5121.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2007 DENX Software Engineering
+ * (C) Copyright 2007, 2008 DENX Software Engineering
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -27,6 +27,7 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#define CONFIG_ADS5121 1
 /*
  * Memory map for the ADS5121 board:
  *
@@ -34,6 +35,9 @@
  * 0x3000_0000 - 0x3001_FFFF	SRAM (128 KB)
  * 0x8000_0000 - 0x803F_FFFF	IMMR (4 MB)
  * 0x8200_0000 - 0x8200_001F	CPLD (32 B)
+ * 0x8400_0000 - 0x82FF_FFFF	PCI I/O space (16 MB)
+ * 0xA000_0000 - 0xAFFF_FFFF	PCI memory space (256 MB)
+ * 0xB000_0000 - 0xBFFF_FFFF	PCI memory mapped I/O space (256 MB)
  * 0xFC00_0000 - 0xFFFF_FFFF	NOR Boot FLASH (64 MB)
  */
 
@@ -42,14 +46,30 @@
  */
 #define CONFIG_E300		1	/* E300 Family */
 #define CONFIG_MPC512X		1	/* MPC512X family */
+#define CONFIG_FSL_DIU_FB	1	/* FSL DIU */
 
-#undef CONFIG_PCI
+/* video */
+#undef CONFIG_VIDEO
 
+#if defined(CONFIG_VIDEO)
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#endif
+
+/* CONFIG_PCI is defined at config time */
+
+#ifdef CONFIG_ADS5121_REV2
 #define CFG_MPC512X_CLKIN	66000000	/* in Hz */
+#else
+#define CFG_MPC512X_CLKIN	33333333	/* in Hz */
+#define CONFIG_PCI
+#endif
 
 #define CONFIG_BOARD_EARLY_INIT_F		/* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R
 
 #define CFG_IMMR		0x80000000
+#define CFG_DIU_ADDR		(CFG_IMMR+0x2100)
 
 #define CFG_MEMTEST_START	0x00200000      /* memtest region */
 #define CFG_MEMTEST_END		0x00400000
@@ -57,7 +77,11 @@
 /*
  * DDR Setup - manually set all parameters as there's no SPD etc.
  */
+#ifdef CONFIG_ADS5121_REV2
 #define CFG_DDR_SIZE		256		/* MB */
+#else
+#define CFG_DDR_SIZE		512		/* MB */
+#endif
 #define CFG_DDR_BASE		0x00000000	/* DDR is system memory*/
 #define CFG_SDRAM_BASE		CFG_DDR_BASE
 
@@ -105,14 +129,20 @@
  *	[09:05]	DRAM tRP:
  *	[04:00] DRAM tRPA
  */
-
+#ifdef CONFIG_ADS5121_REV2
 #define CFG_MDDRC_SYS_CFG	0xF8604A00
 #define CFG_MDDRC_SYS_CFG_RUN	0xE8604A00
+#define CFG_MDDRC_TIME_CFG1	0x54EC1168
+#define CFG_MDDRC_TIME_CFG2	0x35210864
+#else
+#define CFG_MDDRC_SYS_CFG	 0xFA804A00
+#define CFG_MDDRC_SYS_CFG_RUN	 0xEA804A00
+#define CFG_MDDRC_TIME_CFG1	 0x68EC1168
+#define CFG_MDDRC_TIME_CFG2	 0x34310864
+#endif
 #define CFG_MDDRC_SYS_CFG_EN	0xF0000000
 #define CFG_MDDRC_TIME_CFG0	0x00003D2E
 #define CFG_MDDRC_TIME_CFG0_RUN	0x06183D2E
-#define CFG_MDDRC_TIME_CFG1	0x54EC1168
-#define CFG_MDDRC_TIME_CFG2	0x35210864
 
 #define CFG_MICRON_NOP		0x01380000
 #define CFG_MICRON_PCHG_ALL	0x01100400
@@ -124,41 +154,46 @@
 #define CFG_MICRON_OCD_DEFAULT	0x01010780
 
 /* DDR Priority Manager Configuration */
-#define CFG_MDDRCGRP_PM_CFG1	0x000777AA
-#define CFG_MDDRCGRP_PM_CFG2	0x00000055
-#define CFG_MDDRCGRP_HIPRIO_CFG	0x00000000
-#define CFG_MDDRCGRP_LUT0_MU    0x11111117
-#define CFG_MDDRCGRP_LUT0_ML	0x7777777A
-#define CFG_MDDRCGRP_LUT1_MU    0x4444EEEE
-#define CFG_MDDRCGRP_LUT1_ML	0xEEEEEEEE
-#define CFG_MDDRCGRP_LUT2_MU    0x44444444
+#define CFG_MDDRCGRP_PM_CFG1	0x00077777
+#define CFG_MDDRCGRP_PM_CFG2	0x00000000
+#define CFG_MDDRCGRP_HIPRIO_CFG	0x00000001
+#define CFG_MDDRCGRP_LUT0_MU	0xFFEEDDCC
+#define CFG_MDDRCGRP_LUT0_ML	0xBBAAAAAA
+#define CFG_MDDRCGRP_LUT1_MU	0x66666666
+#define CFG_MDDRCGRP_LUT1_ML	0x55555555
+#define CFG_MDDRCGRP_LUT2_MU	0x44444444
 #define CFG_MDDRCGRP_LUT2_ML	0x44444444
-#define CFG_MDDRCGRP_LUT3_MU    0x55555555
+#define CFG_MDDRCGRP_LUT3_MU	0x55555555
 #define CFG_MDDRCGRP_LUT3_ML	0x55555558
-#define CFG_MDDRCGRP_LUT4_MU    0x11111111
-#define CFG_MDDRCGRP_LUT4_ML	0x1111117C
-#define CFG_MDDRCGRP_LUT0_AU    0x33333377
-#define CFG_MDDRCGRP_LUT0_AL	0x7777EEEE
-#define CFG_MDDRCGRP_LUT1_AU    0x11111111
-#define CFG_MDDRCGRP_LUT1_AL	0x11111111
-#define CFG_MDDRCGRP_LUT2_AU    0x11111111
+#define CFG_MDDRCGRP_LUT4_MU	0x11111111
+#define CFG_MDDRCGRP_LUT4_ML	0x11111122
+#define CFG_MDDRCGRP_LUT0_AU	0xaaaaaaaa
+#define CFG_MDDRCGRP_LUT0_AL	0xaaaaaaaa
+#define CFG_MDDRCGRP_LUT1_AU	0x66666666
+#define CFG_MDDRCGRP_LUT1_AL	0x66666666
+#define CFG_MDDRCGRP_LUT2_AU	0x11111111
 #define CFG_MDDRCGRP_LUT2_AL	0x11111111
-#define CFG_MDDRCGRP_LUT3_AU    0x11111111
+#define CFG_MDDRCGRP_LUT3_AU	0x11111111
 #define CFG_MDDRCGRP_LUT3_AL	0x11111111
-#define CFG_MDDRCGRP_LUT4_AU    0x11111111
+#define CFG_MDDRCGRP_LUT4_AU	0x11111111
 #define CFG_MDDRCGRP_LUT4_AL	0x11111111
 
 /*
  * NOR FLASH on the Local Bus
  */
+#undef CONFIG_BKUP_FLASH
 #define CFG_FLASH_CFI				/* use the Common Flash Interface */
-#define CFG_FLASH_CFI_DRIVER			/* use the CFI driver */
+#define CONFIG_FLASH_CFI_DRIVER			/* use the CFI driver */
+#ifdef CONFIG_BKUP_FLASH
+#define CFG_FLASH_BASE		0xFF800000	/* start of FLASH   */
+#define CFG_FLASH_SIZE		0x00800000	/* max flash size in bytes */
+#else
 #define CFG_FLASH_BASE		0xFC000000	/* start of FLASH   */
 #define CFG_FLASH_SIZE		0x04000000	/* max flash size in bytes */
+#endif
 #define CFG_FLASH_USE_BUFFER_WRITE
-
 #define CFG_MAX_FLASH_BANKS	1		/* number of banks */
-#define CFG_FLASH_BANKS_LIST 	{CFG_FLASH_BASE}
+#define CFG_FLASH_BANKS_LIST	{CFG_FLASH_BASE}
 #define CFG_MAX_FLASH_SECT	256		/* max sectors per device */
 
 #undef CFG_FLASH_CHECKSUM
@@ -175,6 +210,7 @@
 
 #define CFG_CS0_CFG		0x05059310	/* ALE active low, data size 4bytes */
 #define CFG_CS2_CFG		0x05059010	/* ALE active low, data size 1byte */
+#define CFG_CS_ALETIMING	0x00000005	/* Use alternative CS timing for CS0 and CS2 */
 
 /* Use SRAM for initial stack */
 #define CFG_INIT_RAM_ADDR	CFG_SRAM_BASE		/* Initial RAM address */
@@ -186,7 +222,11 @@
 
 #define CFG_MONITOR_BASE	TEXT_BASE		/* Start of monitor */
 #define CFG_MONITOR_LEN		(256 * 1024)		/* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN		(512 * 1024)		/* Reserved for malloc */
+#ifdef	CONFIG_FSL_DIU_FB
+#define CFG_MALLOC_LEN		(6 * 1024 * 1024)	/* Reserved for malloc */
+#else
+#define CFG_MALLOC_LEN		(512 * 1024)
+#endif
 
 /*
  * Serial Port
@@ -217,6 +257,31 @@
 #define CFG_PROMPT_HUSH_PS2 "> "
 #endif
 
+/*
+ * PCI
+ */
+#ifdef CONFIG_PCI
+
+/*
+ * General PCI
+ */
+#define CFG_PCI_MEM_BASE	0xA0000000
+#define CFG_PCI_MEM_PHYS	CFG_PCI_MEM_BASE
+#define CFG_PCI_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCI_MMIO_BASE	(CFG_PCI_MEM_BASE + CFG_PCI_MEM_SIZE)
+#define CFG_PCI_MMIO_PHYS	CFG_PCI_MMIO_BASE
+#define CFG_PCI_MMIO_SIZE	0x10000000	/* 256M */
+#define CFG_PCI_IO_BASE		0x00000000
+#define CFG_PCI_IO_PHYS		0x84000000
+#define CFG_PCI_IO_SIZE		0x01000000	/* 16M */
+
+
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+
+#endif
+
 /* I2C */
 #define CONFIG_HARD_I2C			/* I2C with hardware support */
 #undef CONFIG_SOFT_I2C			/* so disable bit-banged I2C */
@@ -243,14 +308,14 @@
 #define CONFIG_NET_MULTI
 #define CONFIG_PHY_ADDR		0x1
 #define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_FEC_AN_TIMEOUT	1
+#define CONFIG_HAS_ETH0
 
-#if 0
 /*
  * Configure on-board RTC
  */
-#define CONFIG_RTC_DS1374			/* use ds1374 rtc via i2c	*/
+#define CONFIG_RTC_M41T62			/* use M41T62 rtc via i2 */
 #define CFG_I2C_RTC_ADDR		0x68	/* at address 0x68		*/
-#endif
 
 /*
  * Environment
@@ -259,7 +324,11 @@
 /* This has to be a multiple of the Flash sector size */
 #define CFG_ENV_ADDR		(CFG_MONITOR_BASE + CFG_MONITOR_LEN)
 #define CFG_ENV_SIZE		0x2000
+#ifdef CONFIG_BKUP_FLASH
+#define CFG_ENV_SECT_SIZE	0x20000	/* one sector (256K) for env */
+#else
 #define CFG_ENV_SECT_SIZE	0x40000	/* one sector (256K) for env */
+#endif
 
 /* Address and size of Redundant Environment Sector	*/
 #define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
@@ -278,6 +347,7 @@
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_DATE
 
 #if defined(CONFIG_PCI)
 #define CONFIG_CMD_PCI
@@ -329,6 +399,8 @@
 #define CFG_HID0_FINAL	HID0_ENABLE_MACHINE_CHECK
 #define CFG_HID2	HID2_HBE
 
+#define CONFIG_HIGH_BATS	1	/* High BATs supported */
+
 /*
  * Internal Definitions
  *
@@ -349,6 +421,7 @@
 
 #define CONFIG_HOSTNAME		ads5121
 #define CONFIG_BOOTFILE		ads5121/uImage
+#define CONFIG_ROOTPATH		/opt/eldk/pcc_6xx
 
 #define CONFIG_LOADADDR		400000	/* default location for tftp and bootm */
 
@@ -358,21 +431,23 @@
 #define CONFIG_BAUDRATE		115200
 
 #define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"
 
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"u-boot_addr_r=200000\0"					\
-	"kernel_addr_r=200000\0"					\
-	"fdt_addr_r=400000\0"						\
-	"ramdisk_addr_r=500000\0"					\
+	"kernel_addr_r=600000\0"					\
+	"fdt_addr_r=880000\0"						\
+	"ramdisk_addr_r=900000\0"					\
 	"u-boot_addr=FFF00000\0"					\
-	"kernel_addr=FC000000\0"					\
-	"fdt_addr=FC2C0000\0"						\
-	"ramdisk_addr=FC300000\0"					\
+	"kernel_addr=FFC40000\0"					\
+	"fdt_addr=FFEC0000\0"						\
+	"ramdisk_addr=FC040000\0"					\
 	"ramdiskfile=ads5121/uRamdisk\0"				\
-	"fdtfile=ads5121/ads5121.dtb\0"					\
 	"u-boot=ads5121/u-boot.bin\0"					\
+	"bootfile=ads5121/uImage\0"					\
+	"fdtfile=ads5121/ads5121.dtb\0"					\
+	"rootpath=/opt/eldk/ppc_6xx\n"					\
 	"netdev=eth0\0"							\
 	"consdev=ttyPSC0\0"						\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
@@ -384,7 +459,7 @@
 	"addtty=setenv bootargs ${bootargs} "				\
 		"console=${consdev},${baudrate}\0"			\
 	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr_r} - ${fdt_addr}\0"		\
+		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
 	"flash_self=run ramargs addip addtty;"				\
 		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
 	"net_nfs=tftp ${kernel_addr_r} ${bootfile};"			\
@@ -393,10 +468,10 @@
 		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
 	"net_self=tftp ${kernel_addr_r} ${bootfile};"			\
 		"tftp ${ramdisk_addr_r} ${ramdiskfile};"		\
-		"tftp ${fdt_addr} ${fdtfile};"				\
+		"tftp ${fdt_addr_r} ${fdtfile};"			\
 		"run ramargs addip addtty;"				\
-		"bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr}\0"\
-	"load=tftp ${u-boot_addr} ${u-boot}\0"				\
+		"bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\
+	"load=tftp ${u-boot_addr_r} ${u-boot}\0"			\
 	"update=protect off ${u-boot_addr} +${filesize};"		\
 		"era ${u-boot_addr} +${filesize};"			\
 		"cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0"	\
@@ -407,10 +482,10 @@
 
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
+#define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES	1
 
 #define OF_CPU			"PowerPC,5121@0"
-#define OF_SOC			"soc@80000000"
-#define OF_SOC_OLD		"soc5121@80000000"
+#define OF_SOC_COMPAT		"fsl,mpc5121-immr"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
 #define OF_STDOUT_PATH		"/soc@80000000/serial@11300"