X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2FVCMA9.h;h=aeb649e190f1313252f201027b0a23fac3b6f19e;hb=df4a0796e86662536df2387ddcf969c2a704bcc2;hp=5f48a709381f4a39f19a5040972953aaf90c8132;hpb=807522fc9ae49e022c9f3556506b4f4c961b17aa;p=oweals%2Fu-boot.git diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h index 5f48a70938..aeb649e190 100644 --- a/include/configs/VCMA9.h +++ b/include/configs/VCMA9.h @@ -44,31 +44,37 @@ #define USE_920T_MMU 1 #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ #define CONFIG_SETUP_MEMORY_TAGS 1 #define CONFIG_INITRD_TAG 1 -/*********************************************************** - * Command definition - ***********************************************************/ -#define CONFIG_COMMANDS \ - (CONFIG_CMD_DFL | \ - CFG_CMD_CACHE | \ - /*CFG_CMD_JFFS2 |*/ \ - /*CFG_CMD_NAND |*/ \ - CFG_CMD_EEPROM | \ - CFG_CMD_I2C | \ - CFG_CMD_USB | \ - CFG_CMD_REGINFO | \ - CFG_CMD_FAT | \ - CFG_CMD_DATE | \ - CFG_CMD_ELF | \ - CFG_CMD_DHCP | \ - CFG_CMD_PING | \ - CFG_CMD_BSP) - -/* this must be included after the definiton of CONFIG_COMMANDS */ -#include + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_USB +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_FAT +#define CONFIG_CMD_DATE +#define CONFIG_CMD_ELF +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_BSP + #define CFG_HUSH_PARSER #define CFG_PROMPT_HUSH_PS2 "> " @@ -78,14 +84,14 @@ * address 0x50 with 16bit addressing ***********************************************************/ #define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CFG_I2C_SPEED 100000 /* I2C speed */ -#define CFG_I2C_SLAVE 0x7F /* I2C slave addr */ +#define CFG_I2C_SPEED 100000 /* I2C speed */ +#define CFG_I2C_SLAVE 0x7F /* I2C slave addr */ #define CFG_I2C_EEPROM_ADDR 0x50 #define CFG_I2C_EEPROM_ADDR_LEN 2 -#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CFG_ENV_OFFSET 0x000 /* environment starts at offset 0 */ -#define CFG_ENV_SIZE 0x800 /* 2KB should be more than enough */ +#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CONFIG_ENV_OFFSET 0x000 /* environment starts at offset 0 */ +#define CONFIG_ENV_SIZE 0x800 /* 2KB should be more than enough */ #undef CFG_I2C_EEPROM_ADDR_OVERFLOW #define CFG_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes page write mode on 24C256 */ @@ -94,7 +100,7 @@ /* * Size of malloc() pool */ -/*#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024)*/ +/*#define CONFIG_MALLOC_SIZE (CONFIG_ENV_SIZE + 128*1024)*/ #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ #define CFG_MONITOR_LEN (256 * 1024) @@ -105,7 +111,7 @@ */ #define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ #define CS8900_BASE 0x20000300 -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ #define CONFIG_DRIVER_S3C24X0_I2C 1 /* we use the buildin I2C controller */ @@ -139,13 +145,13 @@ #define CONFIG_BOOTDELAY 5 /* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */ /* #define CONFIG_BOOT_RETRY_TIME -10 /XXX* feature is available but not enabled */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */ #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_IPADDR 10.0.0.110 #define CONFIG_SERVERIP 10.0.0.1 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ /* what's this ? it's not used anywhere */ #define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */ @@ -220,12 +226,12 @@ #ifdef CONFIG_AMD_LV800 #define PHYS_FLASH_SIZE 0x00100000 /* 1MB */ #define CFG_MAX_FLASH_SECT (19) /* max number of sectors on one chip */ -#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x0F0000) /* addr of environment */ +#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x0F0000) /* addr of environment */ #endif #ifdef CONFIG_AMD_LV400 #define PHYS_FLASH_SIZE 0x00080000 /* 512KB */ #define CFG_MAX_FLASH_SECT (11) /* max number of sectors on one chip */ -#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x070000) /* addr of environment */ +#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x070000) /* addr of environment */ #endif /* timeout values are in ticks */ @@ -233,8 +239,8 @@ #define CFG_FLASH_WRITE_TOUT (5*CFG_HZ) /* Timeout for Flash Write */ #if 0 -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ #endif @@ -246,9 +252,9 @@ /*----------------------------------------------------------------------- * NAND flash settings */ -#if (CONFIG_COMMANDS & CFG_CMD_NAND) +#if defined(CONFIG_CMD_NAND) -#define CFG_NAND_LEGACY +#define CONFIG_NAND_LEGACY #define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ #define SECTORSIZE 512 @@ -256,7 +262,7 @@ #define ADDR_PAGE 2 #define ADDR_COLUMN_PAGE 3 -#define NAND_ChipID_UNKNOWN 0x00 +#define NAND_ChipID_UNKNOWN 0x00 #define NAND_MAX_FLOORS 1 #define NAND_MAX_CHIPS 1 @@ -280,6 +286,6 @@ #define CONFIG_MTD_NAND_VERIFY_WRITE 1 #define CONFIG_MTD_NAND_ECC_JFFS2 1 -#endif /* CONFIG_COMMANDS & CFG_CMD_NAND */ +#endif #endif /* __CONFIG_H */