X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2FTQM885D.h;h=184cb62e19c66e7a4409bdb4de126c00ad4c507a;hb=75eb9976b78ace0e667c1f5faf367acfaed141df;hp=e6b1e35d5413c0b24fcc5e06d6f79cf5b0e1ab01;hpb=1a4596601fd395f3afb8f82f3f840c5e00bdd57a;p=oweals%2Fu-boot.git

diff --git a/include/configs/TQM885D.h b/include/configs/TQM885D.h
index e6b1e35d54..184cb62e19 100644
--- a/include/configs/TQM885D.h
+++ b/include/configs/TQM885D.h
@@ -1,11 +1,11 @@
 /*
- * (C) Copyright 2000-2005
+ * (C) Copyright 2000-2014
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * (C) Copyright 2006
  * Martin Krause, TQ-Systems GmBH, martin.krause@tqs.de
  *
- * SPDX-License-Identifier:	GPL-2.0+ 
+ * SPDX-License-Identifier:	GPL-2.0+
  */
 
 /*
@@ -35,11 +35,9 @@
 #define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
 #define CONFIG_SYS_SMC_RXBUFLEN	128
 #define CONFIG_SYS_MAXIDLE	10
-#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
 
 #define CONFIG_BOOTCOUNT_LIMIT
 
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 
 #define CONFIG_BOARD_TYPES	1	/* support board types		*/
 
@@ -80,18 +78,13 @@
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
-
 #undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-
-#define CONFIG_SYS_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE
-
-#ifdef CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -107,7 +100,6 @@
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-#endif	/* CONFIG_SOFT_I2C */
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C??	*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2		/* two byte address	*/
@@ -126,40 +118,20 @@
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_BOOTFILESIZE
 
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
 #undef CONFIG_RTC_MPC8xx		/* MPC885 does not support RTC	*/
 
 #define	CONFIG_TIMESTAMP		/* but print image timestmps	*/
 
-
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-
 
 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt	*/
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
@@ -177,13 +149,6 @@
 
 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
 
-#define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks */
-
-/*
- * Enable loopw command.
- */
-#define CONFIG_LOOPW
-
 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
@@ -481,9 +446,6 @@
 
 #define CONFIG_ETHPRIME		"SCC"
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
 #define CONFIG_HWCONFIG		1
 
 #endif	/* __CONFIG_H */