X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=include%2Fconfigs%2FPLU405.h;h=0bd77c07b653711a4ddcb57f773644d56a27cdc2;hb=7c6237b3e2f2ee0098897da39b79aff4642b8946;hp=ef5ecba220f38a39d38faf2c92443dd43426e195;hpb=bd84ee4c2020c3a6861f4bb2e7ea0fb49f82e803;p=oweals%2Fu-boot.git

diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index ef5ecba220..0bd77c07b6 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -61,19 +61,34 @@
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
-#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_PCI	| \
-				CFG_CMD_IRQ	| \
-				CFG_CMD_IDE	| \
-				CFG_CMD_FAT	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_NAND	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_EEPROM	)
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_EEPROM
+
 
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
@@ -82,9 +97,6 @@
 
 #define CONFIG_AUTO_UPDATE      1       /* autoupdate via compactflash  */
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_RTC_MC146818		/* DS1685 is MC146818 compatible*/
@@ -103,7 +115,7 @@
 #define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -165,7 +177,8 @@
 #define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
 #define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
-#define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
+#define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
+#define CFG_NAND_QUIET          1
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -275,6 +288,7 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
+#define CFG_EEPROM_WREN         1
 
 /* CAT24WC08/16... */
 #define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
@@ -286,16 +300,6 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
-					/* have only 8kB, 16kB is save here	*/
-#define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */
@@ -376,15 +380,16 @@
  * GPIO0[28-29] - UART1 data signal input/output
  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
  */
-#define CFG_GPIO0_OSRH		0x40000550
+#define CFG_GPIO0_OSRH		0x00000550
 #define CFG_GPIO0_OSRL		0x00000110
 #define CFG_GPIO0_ISR1H		0x00000000
 #define CFG_GPIO0_ISR1L		0x15555445
 #define CFG_GPIO0_TSRH		0x00000000
 #define CFG_GPIO0_TSRL		0x00000000
-#define CFG_GPIO0_TCR		0xF7FE0014
+#define CFG_GPIO0_TCR		0x77FE0014
 
 #define CFG_DUART_RST		(0x80000000 >> 14)
+#define CFG_EEPROM_WP		(0x80000000 >> 0)
 
 /*
  * Internal Definitions