X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=drivers%2Fpower%2FKconfig;h=d8c107e2069f1ee6c0eca33d90f9e870ded5ee3d;hb=5c84ad097d829bb1e6460438f33e1536b23b3c9b;hp=e68e16b3211757271a27e99d0089fbf4b29fc83f;hpb=4608f37918e5d93d6b2b6909b325a5e6fb0a2346;p=oweals%2Fu-boot.git diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index e68e16b321..d8c107e206 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -1,65 +1,319 @@ +menu "Power" + +source "drivers/power/domain/Kconfig" + +source "drivers/power/pmic/Kconfig" + +source "drivers/power/regulator/Kconfig" + +choice + prompt "Select Sunxi PMIC Variant" + depends on ARCH_SUNXI + default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I + default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40 + default AXP818_POWER if MACH_SUN8I_A83T + default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I + +config SUNXI_NO_PMIC + bool "board without a pmic" + ---help--- + Select this for boards which do not use a PMIC. + +config AXP152_POWER + bool "axp152 pmic support" + depends on MACH_SUN5I + select CMD_POWEROFF + ---help--- + Select this to enable support for the axp152 pmic found on most + A10s boards. + +config AXP209_POWER + bool "axp209 pmic support" + depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I + select CMD_POWEROFF + ---help--- + Select this to enable support for the axp209 pmic found on most + A10, A13 and A20 boards. + config AXP221_POWER - boolean "axp221 / axp223 pmic support" - depends on MACH_SUN6I || MACH_SUN8I - default y - ---help--- - Say y here to enable support for the axp221 / axp223 pmic found on most - sun6i (A31) / sun8i (A23) boards. - -config AXP221_DCDC1_VOLT - int "axp221 dcdc1 voltage" - depends on AXP221_POWER - default 3000 - ---help--- - Set the voltage (mV) to program the axp221 dcdc1 at, set to 0 to - disable dcdc1. This is typically used as generic 3.3V IO voltage for - things like GPIO-s, sdcard interfaces, etc. On most boards this is - undervolted to 3.0V to safe battery. - -config AXP221_DLDO1_VOLT - int "axp221 dldo1 voltage" - depends on AXP221_POWER + bool "axp221 / axp223 pmic support" + depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40 + select CMD_POWEROFF + ---help--- + Select this to enable support for the axp221/axp223 pmic found on most + A23 and A31 boards. + +config AXP809_POWER + bool "axp809 pmic support" + depends on MACH_SUN9I + select CMD_POWEROFF + ---help--- + Say y here to enable support for the axp809 pmic found on A80 boards. + +config AXP818_POWER + bool "axp818 pmic support" + depends on MACH_SUN8I_A83T + select CMD_POWEROFF + ---help--- + Say y here to enable support for the axp818 pmic found on + A83T dev board. + +config SY8106A_POWER + bool "SY8106A pmic support" + depends on MACH_SUNXI_H3_H5 + ---help--- + Select this to enable support for the SY8106A pmic found on some + H3 boards. + +endchoice + +config AXP_DCDC1_VOLT + int "axp pmic dcdc1 voltage" + depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + default 3300 if AXP818_POWER || MACH_SUN8I_R40 + default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I + ---help--- + Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to + disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for + generic 3.3V IO voltage for external devices like the lcd-panal and + sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to + save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T + dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally + powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG. + +config AXP_DCDC2_VOLT + int "axp pmic dcdc2 voltage" + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER + default 900 if AXP818_POWER + default 1400 if AXP152_POWER || AXP209_POWER + default 1200 if MACH_SUN6I + default 1100 if MACH_SUN8I + default 0 if MACH_SUN9I + ---help--- + Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to + disable dcdc2. + On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V. + On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V. + On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V. + On A80 boards dcdc2 powers the GPU and can be left off. + On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V. + On R40 boards dcdc2 is VDD-CPU and should be 1.1V + +config AXP_DCDC3_VOLT + int "axp pmic dcdc3 voltage" + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER + default 900 if AXP809_POWER || AXP818_POWER + default 1500 if AXP152_POWER + default 1250 if AXP209_POWER + default 1100 if MACH_SUN8I_R40 + default 1200 if MACH_SUN6I || MACH_SUN8I + ---help--- + Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to + disable dcdc3. + On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and + should be 1.25V. + On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V. + On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V. + On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V. + On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V. + On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V. + +config AXP_DCDC4_VOLT + int "axp pmic dcdc4 voltage" + depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER + default 1250 if AXP152_POWER + default 1200 if MACH_SUN6I + default 0 if MACH_SUN8I + default 900 if MACH_SUN9I + ---help--- + Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to + disable dcdc4. + On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V. + On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V. + On A23 / A33 boards dcdc4 is unused and should be disabled. + On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V. + On A83T boards dcdc4 is used for VDD-GPU. + +config AXP_DCDC5_VOLT + int "axp pmic dcdc5 voltage" + depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I + ---help--- + Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to + disable dcdc5. + On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and + should be 1.5V, 1.35V if DDR3L is used. + +config AXP_ALDO1_VOLT + int "axp pmic (a)ldo1 voltage" + depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + default 0 if MACH_SUN6I || MACH_SUN8I_R40 + default 1800 if MACH_SUN8I_A83T + default 3000 if MACH_SUN8I || MACH_SUN9I + ---help--- + Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to + disable aldo1. + On A31 boards aldo1 is often used to power the wifi module. + On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V. + On A80 boards aldo1 powers the USB hosts and should be 3.0V. + On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and + should be 1.8V. + +config AXP_ALDO2_VOLT + int "axp pmic (a)ldo2 voltage" + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER + default 3000 if AXP152_POWER || AXP209_POWER + default 0 if MACH_SUN6I || MACH_SUN9I + default 1800 if MACH_SUN8I_A83T + default 2500 if MACH_SUN8I + ---help--- + Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to + disable aldo2. + On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V. + On A31 boards aldo2 is typically unused and should be disabled. + On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V. + On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V. + On A80 boards aldo2 powers PB pingroup and camera IO and can be left off. + On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC, + LPDDR2, and the codec. It should be 1.8V. + +config AXP_ALDO3_VOLT + int "axp pmic (a)ldo3 voltage" + depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER + default 0 if AXP209_POWER || MACH_SUN9I + default 3000 if MACH_SUN6I || MACH_SUN8I + ---help--- + Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to + disable aldo3. + On A10(s) / A13 / A20 boards aldo3 should be 2.8V. + On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should + be 3.0V. + On A80 boards aldo3 is normally not used. + On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be + 3.0V. + +config AXP_ALDO4_VOLT + int "axp pmic (a)ldo4 voltage" + depends on AXP209_POWER + default 0 if AXP209_POWER + ---help--- + Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to + disable aldo4. + On A10(s) / A13 / A20 boards aldo4 should be 2.8V. + +config AXP_DLDO1_VOLT + int "axp pmic dldo1 voltage" + depends on AXP221_POWER || AXP809_POWER || AXP818_POWER default 0 ---help--- - Set the voltage (mV) to program the axp221 dldo1 at, set to 0 to - disable dldo1. On sun6i (A31) boards with ethernet this is often used - to power the ethernet phy. On sun8i (A23) boards this is often used to - power the wifi. + Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to + disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used + to power the ethernet phy. On A23, A33 and A80 boards this is often + used to power the wifi. -config AXP221_DLDO4_VOLT - int "axp221 dldo4 voltage" - depends on AXP221_POWER +config AXP_DLDO2_VOLT + int "axp pmic dldo2 voltage" + depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + default 3000 if MACH_SUN9I default 0 ---help--- - Set the voltage (mV) to program the axp221 dldo4 at, set to 0 to + Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to + disable dldo2. + On A80 boards dldo2 normally powers the PL pins and should be 3.0V. + +config AXP_DLDO3_VOLT + int "axp pmic dldo3 voltage" + depends on AXP221_POWER || AXP818_POWER + default 0 + ---help--- + Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to + disable dldo3. + +config AXP_DLDO4_VOLT + int "axp pmic dldo4 voltage" + depends on AXP221_POWER || AXP818_POWER + default 0 + ---help--- + Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to disable dldo4. -config AXP221_ALDO1_VOLT - int "axp221 aldo1 voltage" - depends on AXP221_POWER +config AXP_ELDO1_VOLT + int "axp pmic eldo1 voltage" + depends on AXP221_POWER || AXP809_POWER || AXP818_POWER default 0 ---help--- - Set the voltage (mV) to program the axp221 aldo1 at, set to 0 to - disable aldo1. On sun6i (A31) boards which have a wifi module this is - often used to power the wifi module. + Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to + disable eldo1. -config AXP221_ALDO2_VOLT - int "axp221 aldo2 voltage" - depends on AXP221_POWER - default 0 if MACH_SUN6I - default 2500 if MACH_SUN8I +config AXP_ELDO2_VOLT + int "axp pmic eldo2 voltage" + depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + default 0 ---help--- - Set the voltage (mV) to program the axp221 aldo2 at, set to 0 to - disable aldo2. On sun6i (A31) boards this is typically unused and - should be disabled, if it is used for LPDDR2 it should be set to 1.8V. - On sun8i (A23) this is typically connected to VDD-DLL and must be set - to 2.5V. + Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to + disable eldo2. -config AXP221_ALDO3_VOLT - int "axp221 aldo3 voltage" - depends on AXP221_POWER - default 3000 +config AXP_ELDO3_VOLT + int "axp pmic eldo3 voltage" + depends on AXP221_POWER || AXP809_POWER || AXP818_POWER + default 3000 if MACH_SUN9I + default 0 + ---help--- + Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to + disable eldo3. On some A31(s) tablets it might be used to supply + 1.2V for the SSD2828 chip (converter of parallel LCD interface + into MIPI DSI). + On A80 boards it powers the PM pingroup and should be 3.0V. + +config AXP_FLDO1_VOLT + int "axp pmic fldo1 voltage" + depends on AXP818_POWER + default 0 if MACH_SUN8I_A83T + ---help--- + Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to + disable fldo1. + On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is + used. + +config AXP_FLDO2_VOLT + int "axp pmic fldo2 voltage" + depends on AXP818_POWER + default 900 if MACH_SUN8I_A83T + ---help--- + Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to + disable fldo2. + On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V. + +config AXP_FLDO3_VOLT + int "axp pmic fldo3 voltage" + depends on AXP818_POWER + default 0 ---help--- - Set the voltage (mV) to program the axp221 aldo3 at, set to 0 to - disable aldo3. This is typically connected to VCC-PLL and AVCC and - must be set to 3V. + Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to + disable fldo3. + +config AXP_SW_ON + bool "axp pmic sw on" + depends on AXP809_POWER || AXP818_POWER + default n + ---help--- + Enable to turn on axp pmic sw. + +config SY8106A_VOUT1_VOLT + int "SY8106A pmic VOUT1 voltage" + depends on SY8106A_POWER + default 1200 + ---help--- + Set the voltage (mV) to program the SY8106A pmic VOUT1. This + is typically used to power the VDD-CPU and should be 1200mV. + Values can range from 680mV till 1950mV. + +config TWL4030_POWER + depends on OMAP34XX + bool "Enable driver for TI TWL4030 power management chip" + imply CMD_POWEROFF + ---help--- + The TWL4030 in a combination audio CODEC/power management with + GPIO and it is commonly used with the OMAP3 family of processors + +endmenu