X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=drivers%2Fnet%2Fphy%2FKconfig;h=3dc0822d9c21cfa83591be5791fcdd7a5066a7c6;hb=522e035441ca04d99de2fc13b614ad896691e9c9;hp=95b753432363d5f5e53d6cbb3f8041147aba9417;hpb=da54e7e5a912565ab5979093044d65535f359f40;p=oweals%2Fu-boot.git

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 95b7534323..3dc0822d9c 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -7,11 +7,27 @@ config MV88E6352_SWITCH
 
 menuconfig PHYLIB
 	bool "Ethernet PHY (physical media interface) support"
+	depends on NET
 	help
 	  Enable Ethernet PHY (physical media interface) support.
 
 if PHYLIB
 
+config PHY_ADDR_ENABLE
+	bool "Limit phy address"
+	default y if ARCH_SUNXI
+	help
+	  Select this if you want to control which phy address is used
+
+if PHY_ADDR_ENABLE
+config PHY_ADDR
+	int "PHY address"
+	default 1 if ARCH_SUNXI
+	default 0
+	help
+	  The address of PHY on MII bus. Usually in range of 0 to 31.
+endif
+
 config B53_SWITCH
 	bool "Broadcom BCM53xx (RoboSwitch) Ethernet switch PHY support."
 	help
@@ -48,8 +64,32 @@ endif # MV88E61XX_SWITCH
 config PHYLIB_10G
 	bool "Generic 10G PHY support"
 
-config PHY_AQUANTIA
+menuconfig PHY_AQUANTIA
 	bool "Aquantia Ethernet PHYs support"
+	select PHY_GIGE
+	select PHYLIB_10G
+
+config PHY_AQUANTIA_UPLOAD_FW
+	bool "Aquantia firmware loading support"
+	default n
+	depends on PHY_AQUANTIA
+	help
+		Aquantia PHYs use firmware which can be either loaded automatically
+		from storage directly attached to the phy or loaded by the boot loader
+		via MDIO commands.  The firmware is loaded from a file, specified by
+		the PHY_AQUANTIA_FW_PART and PHY_AQUANTIA_FW_NAME options.
+
+config PHY_AQUANTIA_FW_PART
+	string "Aquantia firmware partition"
+	depends on PHY_AQUANTIA_UPLOAD_FW
+	help
+		Partition containing the firmware file.
+
+config PHY_AQUANTIA_FW_NAME
+	string "Aquantia firmware filename"
+	depends on PHY_AQUANTIA_UPLOAD_FW
+	help
+		Firmware filename.
 
 config PHY_ATHEROS
 	bool "Atheros Ethernet PHYs support"
@@ -131,6 +171,16 @@ config PHY_NATSEMI
 config PHY_REALTEK
 	bool "Realtek Ethernet PHYs support"
 
+config RTL8211E_PINE64_GIGABIT_FIX
+	bool "Fix gigabit throughput on some Pine64+ models"
+	depends on PHY_REALTEK
+	help
+	  Configure the Realtek RTL8211E found on some Pine64+ models differently to
+	  fix throughput on Gigabit links, turning off all internal delays in the
+	  process. The settings that this touches are not documented in the CONFREG
+	  section of the RTL8211E datasheet, but come from Realtek by way of the
+	  Pine64 engineering team.
+
 config RTL8211X_PHY_FORCE_MASTER
 	bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
 	depends on PHY_REALTEK