X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=doc%2FREADME.omap3;h=a62c3574054d5a9cb36d918d3c35766967e81d81;hb=ca88b9b93916f66c6737527aa955d2c1b4758080;hp=1768cdd3592407936bec1d72c2bb0e6ed07acaa4;hpb=3b690ebbbf21303a3bac1f62d967c36cd8655ce0;p=oweals%2Fu-boot.git

diff --git a/doc/README.omap3 b/doc/README.omap3
index 1768cdd359..a62c357405 100644
--- a/doc/README.omap3
+++ b/doc/README.omap3
@@ -68,6 +68,11 @@ make
 make cm_t35_config
 make
 
+* BlueLYNX-X:
+
+make omap3_mvblx_config
+make
+
 Custom commands
 ===============
 
@@ -95,6 +100,7 @@ Interfaces
 ==========
 
 gpio
+----
 
 To set a bit :
 
@@ -122,6 +128,50 @@ To read a bit :
 	else
 		printf("GPIO N is clear\n");
 
+dma
+---
+void omap3_dma_init(void)
+	Init the DMA module
+int omap3_dma_get_conf_chan(uint32_t chan, struct dma4_chan *config);
+	Read config of the channel
+int omap3_dma_conf_chan(uint32_t chan, struct dma4_chan *config);
+	Write config to the channel
+int omap3_dma_conf_transfer(uint32_t chan, uint32_t *src, uint32_t *dst,
+		uint32_t sze)
+	Config source, destination and size of a transfer
+int omap3_dma_wait_for_transfer(uint32_t chan)
+	Wait for a transfer to end - this hast to be called before a channel
+	or the data the channel transferd are used.
+int omap3_dma_get_revision(uint32_t *minor, uint32_t *major)
+	Read silicon Revision of the DMA module
+
+NAND
+====
+
+There are some OMAP3 devices out there with NAND attached. Due to the fact that
+OMAP3 ROM code can only handle 1-bit hamming ECC for accessing first page
+(place where SPL lives) we require this setup for u-boot at least when reading
+the second progam within SPL.  A lot of newer NAND chips however require more
+than 1-bit ECC for the pages, some can live with 1-bit for the first page. To
+handle this we can switch to another ECC algorithm after reading the payload
+within SPL.
+
+BCH8
+----
+
+To enable hardware assisted BCH8 (8-bit BCH [Bose, Chaudhuri, Hocquenghem]) on
+OMAP3 devices we can use the BCH library in lib/bch.c. To do so add CONFIG_BCH
+and set CONFIG_NAND_OMAP_ECCSCHEME=5 (refer README.nand) for selecting BCH8_SW.
+The NAND OOB layout is the same as in linux kernel, if the linux kernel BCH8
+implementation for OMAP3 works for you so the u-boot version should also.
+When you require the SPL to read with BCH8 there are two more configs to
+change:
+
+ * CONFIG_SYS_NAND_ECCPOS (must be the same as .eccpos in
+   GPMC_NAND_HW_BCH8_ECC_LAYOUT defined in
+   arch/arm/include/asm/arch-omap3/omap_gpmc.h)
+ * CONFIG_SYS_NAND_ECCSIZE must be 512
+ * CONFIG_SYS_NAND_ECCBYTES must be 13 for this BCH8 setup
 
 Acknowledgements
 ================