X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=board%2Fmotionpro%2Fmotionpro.c;h=6eb5fe9cfc9950a914e9ebfad3d274a9cc701e6a;hb=98c440bee623ecdd5322852732b883e696fb2140;hp=1729ae74166f0478e796d36cf4cfa7cd58b1928f;hpb=c75e639630cc132dc19cd1ecda5922c0db0bfbba;p=oweals%2Fu-boot.git

diff --git a/board/motionpro/motionpro.c b/board/motionpro/motionpro.c
index 1729ae7416..6eb5fe9cfc 100644
--- a/board/motionpro/motionpro.c
+++ b/board/motionpro/motionpro.c
@@ -28,7 +28,7 @@
 
 #include <common.h>
 #include <mpc5xxx.h>
-
+#include <miiphy.h>
 #if defined(CONFIG_OF_FLAT_TREE)
 #include <ft_build.h>
 #endif
@@ -82,11 +82,27 @@ int board_early_init_r(void)
 }
 
 
+/*
+ * Additional PHY intialization. After being reset in mpc5xxx_fec_init_phy(),
+ * PHY goes into FX mode.  To take it out of the FX mode and switch into
+ * desired TX operation, one needs to clear the FX_SEL bit of Mode Control
+ * Register.
+ */
+void reset_phy(void)
+{
+	unsigned short mode_control;
+
+	miiphy_read("FEC ETHERNET", CONFIG_PHY_ADDR, 0x15, &mode_control);
+	miiphy_write("FEC ETHERNET", CONFIG_PHY_ADDR, 0x15,
+			mode_control & 0xfffe);
+	return;
+}
+
 #ifndef CFG_RAMBOOT
 /*
  * Helper function to initialize SDRAM controller.
  */
-static void sdram_start (int hi_addr)
+static void sdram_start(int hi_addr)
 {
 	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
 
@@ -118,7 +134,7 @@ static void sdram_start (int hi_addr)
 /*
  * Initalize SDRAM - configure SDRAM controller, detect memory size.
  */
-long int initdram (int board_type)
+long int initdram(int board_type)
 {
 	ulong dramsize = 0;
 #ifndef CFG_RAMBOOT
@@ -148,11 +164,12 @@ long int initdram (int board_type)
 		dramsize = 0;
 
 	/* set SDRAM CS0 size according to the amount of RAM found */
-	if (dramsize > 0)
+	if (dramsize > 0) {
 		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 +
 			__builtin_ffs(dramsize >> 20) - 1;
-        else
+	} else {
 		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
+	}
 
 	/* let SDRAM CS1 start right after CS0 and disable it */
 	*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize;
@@ -171,7 +188,7 @@ long int initdram (int board_type)
 }
 
 
-int checkboard (void)
+int checkboard(void)
 {
 	uchar rev = *(vu_char *)CPLD_REV_REGISTER;
 	printf("Board: Promess Motion-PRO board (CPLD rev. 0x%02x)\n", rev);
@@ -188,7 +205,7 @@ void ft_board_setup(void *blob, bd_t *bd)
 
 
 #if defined(CONFIG_STATUS_LED)
-void __led_init (led_id_t regaddr, int state)
+void __led_init(led_id_t regaddr, int state)
 {
 	*((vu_long *) regaddr) |= ENABLE_GPIO_OUT;
 
@@ -198,7 +215,7 @@ void __led_init (led_id_t regaddr, int state)
 		*((vu_long *) regaddr) &= ~LED_ON;
 }
 
-void __led_set (led_id_t regaddr, int state)
+void __led_set(led_id_t regaddr, int state)
 {
 	if (state == STATUS_LED_ON)
 		*((vu_long *) regaddr) |= LED_ON;
@@ -206,7 +223,7 @@ void __led_set (led_id_t regaddr, int state)
 		*((vu_long *) regaddr) &= ~LED_ON;
 }
 
-void __led_toggle (led_id_t regaddr)
+void __led_toggle(led_id_t regaddr)
 {
 	*((vu_long *) regaddr) ^= LED_ON;
 }