X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=board%2Fatmel%2Fat91sam9260ek%2Fat91sam9260ek.c;h=985daf7fb52936eb322cf11d0438335866edfa6a;hb=1332a2a0694c8e10a5bade397cf83645b2c3fd7e;hp=4635f0fb7c442ff418e6d6ec3ba8b3059e17b91e;hpb=c1212b2f5c5ed440bf8e9ebc8e4fd7488858b935;p=oweals%2Fu-boot.git

diff --git a/board/atmel/at91sam9260ek/at91sam9260ek.c b/board/atmel/at91sam9260ek/at91sam9260ek.c
index 4635f0fb7c..985daf7fb5 100644
--- a/board/atmel/at91sam9260ek/at91sam9260ek.c
+++ b/board/atmel/at91sam9260ek/at91sam9260ek.c
@@ -26,13 +26,16 @@
 #include <asm/arch/at91sam9260.h>
 #include <asm/arch/at91sam9260_matrix.h>
 #include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
 #include <asm/arch/at91_pmc.h>
 #include <asm/arch/at91_rstc.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/io.h>
+#include <asm/arch/hardware.h>
 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
 #include <net.h>
 #endif
+#include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -41,33 +44,6 @@ DECLARE_GLOBAL_DATA_PTR;
  * Miscelaneous platform dependent initialisations
  */
 
-static void at91sam9260ek_serial_hw_init(void)
-{
-#ifdef CONFIG_USART0
-	at91_set_A_periph(AT91_PIN_PB4, 1);		/* TXD0 */
-	at91_set_A_periph(AT91_PIN_PB5, 0);		/* RXD0 */
-	at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US0);
-#endif
-
-#ifdef CONFIG_USART1
-	at91_set_A_periph(AT91_PIN_PB6, 1);		/* TXD1 */
-	at91_set_A_periph(AT91_PIN_PB7, 0);		/* RXD1 */
-	at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US1);
-#endif
-
-#ifdef CONFIG_USART2
-	at91_set_A_periph(AT91_PIN_PB8, 1);		/* TXD2 */
-	at91_set_A_periph(AT91_PIN_PB9, 0);		/* RXD2 */
-	at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_US2);
-#endif
-
-#ifdef CONFIG_USART3	/* DBGU */
-	at91_set_A_periph(AT91_PIN_PB14, 0);		/* DRXD */
-	at91_set_A_periph(AT91_PIN_PB15, 1);		/* DTXD */
-	at91_sys_write(AT91_PMC_PCER, 1 << AT91_ID_SYS);
-#endif
-}
-
 #ifdef CONFIG_CMD_NAND
 static void at91sam9260ek_nand_hw_init(void)
 {
@@ -80,8 +56,8 @@ static void at91sam9260ek_nand_hw_init(void)
 
 	/* Configure SMC CS3 for NAND/SmartMedia */
 	at91_sys_write(AT91_SMC_SETUP(3),
-		       AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) |
-		       AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0));
+		       AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
+		       AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
 	at91_sys_write(AT91_SMC_PULSE(3),
 		       AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) |
 		       AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
@@ -90,9 +66,9 @@ static void at91sam9260ek_nand_hw_init(void)
 	at91_sys_write(AT91_SMC_MODE(3),
 		       AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
 		       AT91_SMC_EXNWMODE_DISABLE |
-#ifdef CFG_NAND_DBW_16
+#ifdef CONFIG_SYS_NAND_DBW_16
 		       AT91_SMC_DBW_16 |
-#else /* CFG_NAND_DBW_8 */
+#else /* CONFIG_SYS_NAND_DBW_8 */
 		       AT91_SMC_DBW_8 |
 #endif
 		       AT91_SMC_TDF_(2));
@@ -131,7 +107,7 @@ static void at91sam9260ek_macb_hw_init(void)
 	/*
 	 * Disable pull-up on:
 	 *	RXDV (PA17) => PHY normal mode (not Test mode)
-	 * 	ERX0 (PA14) => PHY ADDR0
+	 *	ERX0 (PA14) => PHY ADDR0
 	 *	ERX1 (PA15) => PHY ADDR1
 	 *	ERX2 (PA25) => PHY ADDR2
 	 *	ERX3 (PA26) => PHY ADDR3
@@ -149,7 +125,7 @@ static void at91sam9260ek_macb_hw_init(void)
 
 	/* Need to reset PHY -> 500ms reset */
 	at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
-				     AT91_RSTC_ERSTL | (0x0D << 8) |
+				     (AT91_RSTC_ERSTL & (0x0D << 8)) |
 				     AT91_RSTC_URSTEN);
 
 	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
@@ -159,7 +135,7 @@ static void at91sam9260ek_macb_hw_init(void)
 
 	/* Restore NRST value */
 	at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
-				     AT91_RSTC_ERSTL | (0x0 << 8) |
+				     (AT91_RSTC_ERSTL & (0x0 << 8)) |
 				     AT91_RSTC_URSTEN);
 
 	/* Re-enable pull-up */
@@ -188,8 +164,17 @@ static void at91sam9260ek_macb_hw_init(void)
 	at91_set_B_periph(AT91_PIN_PA25, 0);	/* ERX2 */
 	at91_set_B_periph(AT91_PIN_PA26, 0);	/* ERX3 */
 	at91_set_B_periph(AT91_PIN_PA27, 0);	/* ERXCK */
+#if defined(CONFIG_AT91SAM9260EK)
+	/*
+	 * use PA10, PA11 for ETX2, ETX3.
+	 * PA23 and PA24 are for TWI EEPROM
+	 */
+	at91_set_B_periph(AT91_PIN_PA10, 0);	/* ETX2 */
+	at91_set_B_periph(AT91_PIN_PA11, 0);	/* ETX3 */
+#else
 	at91_set_B_periph(AT91_PIN_PA23, 0);	/* ETX2 */
 	at91_set_B_periph(AT91_PIN_PA24, 0);	/* ETX3 */
+#endif
 	at91_set_B_periph(AT91_PIN_PA22, 0);	/* ETXER */
 #endif
 
@@ -206,7 +191,7 @@ int board_init(void)
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 
-	at91sam9260ek_serial_hw_init();
+	at91_serial_hw_init();
 #ifdef CONFIG_CMD_NAND
 	at91sam9260ek_nand_hw_init();
 #endif
@@ -239,3 +224,12 @@ void reset_phy(void)
 #endif
 }
 #endif
+
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_MACB
+	rc = macb_eth_initialize(0, (void *)AT91SAM9260_BASE_EMAC, 0x00);
+#endif
+	return rc;
+}