X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=board%2FLEOX%2Felpt860%2Felpt860.c;h=03868cdd7394998fd9129bfbe5374b72595ee8ff;hb=50410078cd587f6b9ee915bd178854c0ee6d9bfe;hp=25645462ff7a7fa02603f24a99e30f383f30d62c;hpb=3bac351370ef7cbf9d2af27ba52bee1703ad677e;p=oweals%2Fu-boot.git diff --git a/board/LEOX/elpt860/elpt860.c b/board/LEOX/elpt860/elpt860.c index 25645462ff..03868cdd73 100644 --- a/board/LEOX/elpt860/elpt860.c +++ b/board/LEOX/elpt860/elpt860.c @@ -33,9 +33,9 @@ /* ** Note 1: In this file, you have to provide the following functions: ** ------ -** int board_pre_init(void) +** int board_early_init_f(void) ** int checkboard(void) -** long int initdram(int board_type) +** phys_size_t initdram(int board_type) ** called from 'board_init_f()' into 'common/board.c' ** ** void reset_phy(void) @@ -53,113 +53,110 @@ static long int dram_size (long int, long int *, long int); #define _NOT_USED_ 0xFFFFFFFF -const uint init_sdram_table[] = -{ - /* - * Single Read. (Offset 0 in UPMA RAM) - */ - 0x0FFCCC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, - 0xFFFFFC04, /* last */ - /* - * SDRAM Initialization (offset 5 in UPMA RAM) - * - * This is no UPM entry point. The following definition uses - * the remaining space to establish an initialization - * sequence, which is executed by a RUN command. - * - */ - 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, /* last */ - /* - * Burst Read. (Offset 8 in UPMA RAM) - */ - 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, - 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, - 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, - 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, /* last */ - /* - * Single Write. (Offset 18 in UPMA RAM) - */ - 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, - 0xFFFFFC04, 0xFFFFFC04, 0x0FFFFC04, 0xFFFFFC04, /* last */ - /* - * Burst Write. (Offset 20 in UPMA RAM) - */ - 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, - 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, - 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC34, 0x0FAC0C34, - 0xFFFFFC05, 0xFFFFFC04, 0x0FFCFC04, 0xFFFFFC05, /* last */ +const uint init_sdram_table[] = { + /* + * Single Read. (Offset 0 in UPMA RAM) + */ + 0x0FFCCC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, + 0xFFFFFC04, /* last */ + /* + * SDRAM Initialization (offset 5 in UPMA RAM) + * + * This is no UPM entry point. The following definition uses + * the remaining space to establish an initialization + * sequence, which is executed by a RUN command. + * + */ + 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, /* last */ + /* + * Burst Read. (Offset 8 in UPMA RAM) + */ + 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, + 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, /* last */ + /* + * Single Write. (Offset 18 in UPMA RAM) + */ + 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, + 0xFFFFFC04, 0xFFFFFC04, 0x0FFFFC04, 0xFFFFFC04, /* last */ + /* + * Burst Write. (Offset 20 in UPMA RAM) + */ + 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC34, 0x0FAC0C34, + 0xFFFFFC05, 0xFFFFFC04, 0x0FFCFC04, 0xFFFFFC05, /* last */ }; -const uint sdram_table[] = -{ - /* - * Single Read. (Offset 0 in UPMA RAM) - */ - 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04, - 0xFF0FFC00, /* last */ - /* - * SDRAM Initialization (offset 5 in UPMA RAM) - * - * This is no UPM entry point. The following definition uses - * the remaining space to establish an initialization - * sequence, which is executed by a RUN command. - * - */ - 0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC05, /* last */ - /* - * Burst Read. (Offset 8 in UPMA RAM) - */ - 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04, - 0xF00FFC00, 0xF00FFC00, 0xF00FFC00, 0xFF0FFC00, - 0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04, - 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */ - /* - * Single Write. (Offset 18 in UPMA RAM) - */ - 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF0C00, - 0xFF0FFC04, 0x0FFCCC04, 0xFFAFFC05, /* last */ - _NOT_USED_, - /* - * Burst Write. (Offset 20 in UPMA RAM) - */ - 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC00, 0x00AF0C00, - 0xF00FFC00, 0xF00FFC00, 0xF00FFC04, 0x0FFCCC04, - 0xFFAFFC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04, - 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */ - /* - * Refresh (Offset 30 in UPMA RAM) - */ - 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, - 0xFFFFFC05, 0xFFFFFC04, 0xFFFFFC05, _NOT_USED_, - 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */ - /* - * Exception. (Offset 3c in UPMA RAM) - */ - 0x0FFFFC34, 0x0FAC0C34, 0xFFFFFC05, 0xFFAFFC04, /* last */ +const uint sdram_table[] = { + /* + * Single Read. (Offset 0 in UPMA RAM) + */ + 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04, + 0xFF0FFC00, /* last */ + /* + * SDRAM Initialization (offset 5 in UPMA RAM) + * + * This is no UPM entry point. The following definition uses + * the remaining space to establish an initialization + * sequence, which is executed by a RUN command. + * + */ + 0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC05, /* last */ + /* + * Burst Read. (Offset 8 in UPMA RAM) + */ + 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04, + 0xF00FFC00, 0xF00FFC00, 0xF00FFC00, 0xFF0FFC00, + 0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04, + 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */ + /* + * Single Write. (Offset 18 in UPMA RAM) + */ + 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF0C00, + 0xFF0FFC04, 0x0FFCCC04, 0xFFAFFC05, /* last */ + _NOT_USED_, + /* + * Burst Write. (Offset 20 in UPMA RAM) + */ + 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC00, 0x00AF0C00, + 0xF00FFC00, 0xF00FFC00, 0xF00FFC04, 0x0FFCCC04, + 0xFFAFFC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04, + 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */ + /* + * Refresh (Offset 30 in UPMA RAM) + */ + 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, + 0xFFFFFC05, 0xFFFFFC04, 0xFFFFFC05, _NOT_USED_, + 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */ + /* + * Exception. (Offset 3c in UPMA RAM) + */ + 0x0FFFFC34, 0x0FAC0C34, 0xFFFFFC05, 0xFFAFFC04, /* last */ }; /* ------------------------------------------------------------------------- */ -#define CFG_PC4 0x0800 +#define CONFIG_SYS_PC4 0x0800 -#define CFG_DS1 CFG_PC4 +#define CONFIG_SYS_DS1 CONFIG_SYS_PC4 /* * Very early board init code (fpga boot, etc.) */ -int -board_pre_init (void) +int board_early_init_f (void) { - volatile immap_t *immr = (immap_t *) CFG_IMMR; + volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR; - /* - * Light up the red led on ELPT860 pcb (DS1) (PCDAT) - */ - immr->im_ioport.iop_pcdat &= ~CFG_DS1; /* PCDAT (DS1 = 0) */ - immr->im_ioport.iop_pcpar &= ~CFG_DS1; /* PCPAR (0=general purpose I/O) */ - immr->im_ioport.iop_pcdir |= CFG_DS1; /* PCDIR (I/O: 0=input, 1=output) */ + /* + * Light up the red led on ELPT860 pcb (DS1) (PCDAT) + */ + immr->im_ioport.iop_pcdat &= ~CONFIG_SYS_DS1; /* PCDAT (DS1 = 0) */ + immr->im_ioport.iop_pcpar &= ~CONFIG_SYS_DS1; /* PCPAR (0=general purpose I/O) */ + immr->im_ioport.iop_pcdir |= CONFIG_SYS_DS1; /* PCDIR (I/O: 0=input, 1=output) */ - return ( 0 ); /* success */ + return (0); /* success */ } /* @@ -170,150 +167,144 @@ board_pre_init (void) * Return 1 if no second DRAM bank, otherwise returns 0 */ -int -checkboard (void) +int checkboard (void) { - unsigned char *s = getenv("serial#"); + char buf[64]; + int i = getenv_f("serial#", buf, sizeof(buf)); + + if ((i < 0) || strncmp(buf, "ELPT860", 7)) + printf ("### No HW ID - assuming ELPT860\n"); - if ( !s || strncmp(s, "ELPT860", 7) ) - printf ("### No HW ID - assuming ELPT860\n"); - - return ( 0 ); /* success */ + return (0); /* success */ } /* ------------------------------------------------------------------------- */ -long int -initdram (int board_type) +phys_size_t initdram (int board_type) { - volatile immap_t *immap = (immap_t *)CFG_IMMR; - volatile memctl8xx_t *memctl = &immap->im_memctl; - long int size8, size9; - long int size_b0 = 0; - - /* - * This sequence initializes SDRAM chips on ELPT860 board - */ - upmconfig(UPMA, (uint *)init_sdram_table, - sizeof(init_sdram_table)/sizeof(uint)); - - memctl->memc_mptpr = 0x0200; - memctl->memc_mamr = 0x18002111; - - memctl->memc_mar = 0x00000088; - memctl->memc_mcr = 0x80002000; /* CS1: SDRAM bank 0 */ - - upmconfig(UPMA, (uint *)sdram_table, - sizeof(sdram_table)/sizeof(uint)); - - /* - * Preliminary prescaler for refresh (depends on number of - * banks): This value is selected for four cycles every 62.4 us - * with two SDRAM banks or four cycles every 31.2 us with one - * bank. It will be adjusted after memory sizing. - */ - memctl->memc_mptpr = CFG_MPTPR_2BK_8K; - - /* - * The following value is used as an address (i.e. opcode) for - * the LOAD MODE REGISTER COMMAND during SDRAM initialisation. If - * the port size is 32bit the SDRAM does NOT "see" the lower two - * address lines, i.e. mar=0x00000088 -> opcode=0x00000022 for - * MICRON SDRAMs: - * -> 0 00 010 0 010 - * | | | | +- Burst Length = 4 - * | | | +----- Burst Type = Sequential - * | | +------- CAS Latency = 2 - * | +----------- Operating Mode = Standard - * +-------------- Write Burst Mode = Programmed Burst Length - */ - memctl->memc_mar = 0x00000088; - - /* - * Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at - * preliminary addresses - these have to be modified after the - * SDRAM size has been determined. - */ - memctl->memc_or1 = CFG_OR1_PRELIM; - memctl->memc_br1 = CFG_BR1_PRELIM; - - memctl->memc_mamr = CFG_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */ - - udelay (200); - - /* perform SDRAM initializsation sequence */ - - memctl->memc_mcr = 0x80002105; /* CS1: SDRAM bank 0 */ - udelay (1); - memctl->memc_mcr = 0x80002230; /* CS1: SDRAM bank 0 - execute twice */ - udelay (1); - - memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */ - - udelay (1000); - - /* - * Check Bank 0 Memory Size for re-configuration - * - * try 8 column mode - */ - size8 = dram_size (CFG_MAMR_8COL, - (ulong *) SDRAM_BASE1_PRELIM, - SDRAM_MAX_SIZE); - - udelay (1000); - - /* - * try 9 column mode - */ - size9 = dram_size (CFG_MAMR_9COL, - (ulong *) SDRAM_BASE1_PRELIM, - SDRAM_MAX_SIZE); - - if ( size8 < size9 ) /* leave configuration at 9 columns */ - { - size_b0 = size9; - /* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */ - } - else /* back to 8 columns */ - { - size_b0 = size8; - memctl->memc_mamr = CFG_MAMR_8COL; - udelay (500); - /* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */ - } - - udelay (1000); - - /* - * Adjust refresh rate depending on SDRAM type, both banks - * For types > 128 MBit leave it at the current (fast) rate - */ - if ( size_b0 < 0x02000000 ) - { - /* reduce to 15.6 us (62.4 us / quad) */ - memctl->memc_mptpr = CFG_MPTPR_2BK_4K; + volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; + volatile memctl8xx_t *memctl = &immap->im_memctl; + long int size8, size9; + long int size_b0 = 0; + + /* + * This sequence initializes SDRAM chips on ELPT860 board + */ + upmconfig (UPMA, (uint *) init_sdram_table, + sizeof (init_sdram_table) / sizeof (uint)); + + memctl->memc_mptpr = 0x0200; + memctl->memc_mamr = 0x18002111; + + memctl->memc_mar = 0x00000088; + memctl->memc_mcr = 0x80002000; /* CS1: SDRAM bank 0 */ + + upmconfig (UPMA, (uint *) sdram_table, + sizeof (sdram_table) / sizeof (uint)); + + /* + * Preliminary prescaler for refresh (depends on number of + * banks): This value is selected for four cycles every 62.4 us + * with two SDRAM banks or four cycles every 31.2 us with one + * bank. It will be adjusted after memory sizing. + */ + memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K; + + /* + * The following value is used as an address (i.e. opcode) for + * the LOAD MODE REGISTER COMMAND during SDRAM initialisation. If + * the port size is 32bit the SDRAM does NOT "see" the lower two + * address lines, i.e. mar=0x00000088 -> opcode=0x00000022 for + * MICRON SDRAMs: + * -> 0 00 010 0 010 + * | | | | +- Burst Length = 4 + * | | | +----- Burst Type = Sequential + * | | +------- CAS Latency = 2 + * | +----------- Operating Mode = Standard + * +-------------- Write Burst Mode = Programmed Burst Length + */ + memctl->memc_mar = 0x00000088; + + /* + * Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at + * preliminary addresses - these have to be modified after the + * SDRAM size has been determined. + */ + memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM; + memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM; + + memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */ + + udelay (200); + + /* perform SDRAM initializsation sequence */ + + memctl->memc_mcr = 0x80002105; /* CS1: SDRAM bank 0 */ + udelay (1); + memctl->memc_mcr = 0x80002230; /* CS1: SDRAM bank 0 - execute twice */ + udelay (1); + + memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */ + + udelay (1000); + + /* + * Check Bank 0 Memory Size for re-configuration + * + * try 8 column mode + */ + size8 = dram_size (CONFIG_SYS_MAMR_8COL, + SDRAM_BASE1_PRELIM, SDRAM_MAX_SIZE); + + udelay (1000); + + /* + * try 9 column mode + */ + size9 = dram_size (CONFIG_SYS_MAMR_9COL, + SDRAM_BASE1_PRELIM, SDRAM_MAX_SIZE); + + if (size8 < size9) { /* leave configuration at 9 columns */ + size_b0 = size9; + /* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */ + } else { /* back to 8 columns */ + + size_b0 = size8; + memctl->memc_mamr = CONFIG_SYS_MAMR_8COL; + udelay (500); + /* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */ + } + udelay (1000); - } - - /* - * Final mapping: map bigger bank first - */ - memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM; - memctl->memc_br1 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V; - - { - unsigned long reg; - - /* adjust refresh rate depending on SDRAM type, one bank */ - reg = memctl->memc_mptpr; - reg >>= 1; /* reduce to CFG_MPTPR_1BK_8K / _4K */ - memctl->memc_mptpr = reg; - } - - udelay(10000); - - return (size_b0); + + /* + * Adjust refresh rate depending on SDRAM type, both banks + * For types > 128 MBit leave it at the current (fast) rate + */ + if (size_b0 < 0x02000000) { + /* reduce to 15.6 us (62.4 us / quad) */ + memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K; + udelay (1000); + } + + /* + * Final mapping: map bigger bank first + */ + memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM; + memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V; + + { + unsigned long reg; + + /* adjust refresh rate depending on SDRAM type, one bank */ + reg = memctl->memc_mptpr; + reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */ + memctl->memc_mptpr = reg; + } + + udelay (10000); + + return (size_b0); } /* ------------------------------------------------------------------------- */ @@ -326,74 +317,33 @@ initdram (int board_type) * - short between data lines */ -static long int -dram_size (long int mamr_value, - long int *base, - long int maxsize) +static long int +dram_size (long int mamr_value, long int *base, long int maxsize) { - volatile immap_t *immap = (immap_t *)CFG_IMMR; - volatile memctl8xx_t *memctl = &immap->im_memctl; - volatile long int *addr; - ulong cnt, val; - ulong save[32]; /* to make test non-destructive */ - unsigned char i = 0; - - memctl->memc_mamr = mamr_value; - - for (cnt = maxsize/sizeof(long); cnt > 0; cnt >>= 1) - { - addr = base + cnt; /* pointer arith! */ - - save[i++] = *addr; - *addr = ~cnt; - } - - /* write 0 to base address */ - addr = base; - save[i] = *addr; - *addr = 0; - - /* check at base address */ - if ( (val = *addr) != 0 ) - { - *addr = save[i]; - - return (0); - } - - for (cnt = 1; cnt <= maxsize/sizeof(long); cnt <<= 1) - { - addr = base + cnt; /* pointer arith! */ - - val = *addr; - *addr = save[--i]; - - if ( val != (~cnt) ) - { - return (cnt * sizeof(long)); - } - } + volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; + volatile memctl8xx_t *memctl = &immap->im_memctl; + + memctl->memc_mamr = mamr_value; - return (maxsize); + return (get_ram_size (base, maxsize)); } /* ------------------------------------------------------------------------- */ -#define CFG_PA1 0x4000 -#define CFG_PA2 0x2000 +#define CONFIG_SYS_PA1 0x4000 +#define CONFIG_SYS_PA2 0x2000 -#define CFG_LBKs (CFG_PA2 | CFG_PA1) +#define CONFIG_SYS_LBKs (CONFIG_SYS_PA2 | CONFIG_SYS_PA1) -void -reset_phy (void) +void reset_phy (void) { - volatile immap_t *immr = (immap_t *) CFG_IMMR; - - /* - * Ensure LBK LXT901 ethernet 1 & 2 = 0 ... for normal loopback in effect - * and no AUI loopback - */ - immr->im_ioport.iop_padat &= ~CFG_LBKs; /* PADAT (LBK eth 1&2 = 0) */ - immr->im_ioport.iop_papar &= ~CFG_LBKs; /* PAPAR (0=general purpose I/O) */ - immr->im_ioport.iop_padir |= CFG_LBKs; /* PADIR (I/O: 0=input, 1=output) */ + volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR; + + /* + * Ensure LBK LXT901 ethernet 1 & 2 = 0 ... for normal loopback in effect + * and no AUI loopback + */ + immr->im_ioport.iop_padat &= ~CONFIG_SYS_LBKs; /* PADAT (LBK eth 1&2 = 0) */ + immr->im_ioport.iop_papar &= ~CONFIG_SYS_LBKs; /* PAPAR (0=general purpose I/O) */ + immr->im_ioport.iop_padir |= CONFIG_SYS_LBKs; /* PADIR (I/O: 0=input, 1=output) */ }