X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=arch%2Farm%2Fdts%2Fzynqmp-zcu100-revC.dts;h=1726edf78ed23a64decc9a9e894526c11c339747;hb=d32cbefc8ac82bd0206f806efb07df82c4b92d5b;hp=05491e9bbc0c309e4fcc5f25f601c21a3c3e6f9d;hpb=9450ab2ba8d720bd9f73bccc0af2e2b5a2c2aaf1;p=oweals%2Fu-boot.git

diff --git a/arch/arm/dts/zynqmp-zcu100-revC.dts b/arch/arm/dts/zynqmp-zcu100-revC.dts
index 05491e9bbc..1726edf78e 100644
--- a/arch/arm/dts/zynqmp-zcu100-revC.dts
+++ b/arch/arm/dts/zynqmp-zcu100-revC.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU100 revC
  *
- * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ * (C) Copyright 2016 - 2020, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  * Nathalie Chan King Choy
@@ -11,7 +11,7 @@
 /dts-v1/;
 
 #include "zynqmp.dtsi"
-#include "zynqmp-clk.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -53,7 +53,7 @@
 			label = "sw4";
 			gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
-			gpio-key,wakeup;
+			wakeup-source;
 			autorepeat;
 		};
 	};
@@ -95,7 +95,7 @@
 			linux,default-trigger = "bluetooth-power";
 		};
 
-		vbus_det { /* U5 USB5744 VBUS detection via MIO25 */
+		vbus-det { /* U5 USB5744 VBUS detection via MIO25 */
 			label = "vbus_det";
 			gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -120,9 +120,15 @@
 		regulator-boot-on;
 	};
 
-	sdio_pwrseq: sdio_pwrseq {
+	sdio_pwrseq: sdio-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */
+		post-power-on-delay-ms = <10>;
+	};
+
+	ina226 {
+		compatible = "iio-hwmon";
+		io-channels = <&u35 0>, <&u35 1>, <&u35 2>, <&u35 3>;
 	};
 };
 
@@ -216,8 +222,9 @@
 			#size-cells = <0>;
 			reg = <5>;
 			/* PS_PMBUS */
-			ina226@40 { /* u35 */
+			u35: ina226@40 { /* u35 */
 				compatible = "ti,ina226";
+				#io-channel-cells = <1>;
 				reg = <0x40>;
 				shunt-resistor = <10000>;
 				/* MIO31 is alert which should be routed to PMUFW */
@@ -296,7 +303,6 @@
 		compatible = "ti,wl1831-st";
 		enable-gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
 	};
-
 };
 
 &uart1 {
@@ -332,7 +338,6 @@
 
 &watchdog0 {
 	status = "okay";
-	reset-on-timeout;
 };
 
 &xilinx_ams {