X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=arch%2Farm%2Fdts%2Fsun8i-h2-plus-orangepi-zero.dts;h=0bc031fe4c56b5a234f73bafd1919ef81d613f54;hb=f301ba55c877707e15378401247cc828740ba00e;hp=e0efcb3ba3edc5a4c630b386735fc5b06223185e;hpb=e294ba0678359bc32085c1714329af37e33e8f16;p=oweals%2Fu-boot.git

diff --git a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
index e0efcb3ba3..0bc031fe4c 100644
--- a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
@@ -49,7 +49,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Xunlong Orange Pi Zero";
@@ -58,6 +57,7 @@
 	aliases {
 		serial0 = &uart0;
 		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+		ethernet0 = &emac;
 		ethernet1 = &xr819;
 	};
 
@@ -92,9 +92,14 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <200>;
 	};
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -107,18 +112,13 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
 &mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_a>;
 	vmmc-supply = <&reg_vcc_wifi>;
 	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
@@ -134,17 +134,56 @@
 	};
 };
 
+&ohci0 {
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
 
+&spi0 {
+	/* Disable SPI NOR by default: it optional on Orange Pi Zero boards */
+	status = "disabled";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
 
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
 &usbphy {
-	/* USB VBUS is always on */
+	/*
+	 * USB Type-A port VBUS is always on. However, MicroUSB VBUS can only
+	 * power up the board; when it's used as OTG port, this VBUS is
+	 * always off even if the board is powered via GPIO pins.
+	 */
 	status = "okay";
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
 };