X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=arch%2Farm%2Fdts%2Fsun50i-a64-bananapi-m64.dts;h=ef1c90401bb2a027a4823ad4e50268a1523beca5;hb=b4944e25744aa42dc23c6912e1cd4ccad270c4e0;hp=dcde4a4881654e1e0c5110320e213a860d1bd908;hpb=90dd2756a0ba67002627549c63764aa2f9919288;p=oweals%2Fu-boot.git

diff --git a/arch/arm/dts/sun50i-a64-bananapi-m64.dts b/arch/arm/dts/sun50i-a64-bananapi-m64.dts
index dcde4a4881..ef1c90401b 100644
--- a/arch/arm/dts/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm/dts/sun50i-a64-bananapi-m64.dts
@@ -1,6 +1,5 @@
 /*
  * Copyright (c) 2016 ARM Ltd.
- * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -52,6 +51,7 @@
 	compatible = "sinovoip,bananapi-m64", "allwinner,sun50i-a64";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 		serial1 = &uart1;
 	};
@@ -60,12 +60,45 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
 	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr-led {
+			label = "bananapi-m64:red:pwr";
+			gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+			default-state = "on";
+		};
+
+		green {
+			label = "bananapi-m64:green:user";
+			gpios = <&pio 4 14 GPIO_ACTIVE_HIGH>; /* PE14 */
+		};
+
+		blue {
+			label = "bananapi-m64:blue:user";
+			gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
+		};
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+	};
+};
+
+&de {
+	status = "okay";
 };
 
 &ehci0 {
@@ -76,6 +109,26 @@
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dc1sw>;
+	status = "okay";
+};
+
+&hdmi {
+	hvcc-supply = <&reg_dldo1>;
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c1_pins>;
@@ -86,12 +139,18 @@
 	bias-pull-up;
 };
 
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	bus-width = <4>;
 	status = "okay";
@@ -100,16 +159,26 @@
 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dldo2>;
+	vqmmc-supply = <&reg_dldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+		interrupt-names = "host-wake";
+	};
 };
 
 &mmc2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -124,9 +193,142 @@
 	status = "okay";
 };
 
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo1 {
+	/*
+	 * This regulator also drives the PE pingroup GPIOs,
+	 * which also controls two LEDs.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "afvcc-csi";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	/*
+	 * This regulator also indirectly drives the PD pingroup GPIOs,
+	 * which also controls the power LED.
+	 */
+	regulator-always-on;
+	regulator-name = "vcc-phy";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&simplefb_hdmi {
+	vcc-hdmi-supply = <&reg_dldo1>;
+};
+
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };
 
@@ -143,5 +345,6 @@
 
 &usbphy {
 	usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+	usb0_vbus-supply = <&reg_drivevbus>;
 	status = "okay";
 };