X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=README;h=37eda1156c59f67fc2b009cb9575c4b557564df0;hb=367c6651a88dda0463f9fbeff3b1ab7ece05b4f9;hp=171e0d6f969e4cc9a7a0cc10dd568bb27ee44ee1;hpb=bbf2abc0f5a5be0b8081ae8587fa90b376160444;p=oweals%2Fu-boot.git diff --git a/README b/README index 171e0d6f96..37eda1156c 100644 --- a/README +++ b/README @@ -675,7 +675,7 @@ The following options need to be configured: (requires CONFIG_CMD_I2C) CONFIG_CMD_SETGETDCR Support for DCR Register access (4xx only) - CONFIG_CMD_SHA1 print sha1 memory digest + CONFIG_CMD_SHA1SUM print sha1 memory digest (requires CONFIG_CMD_MEMORY) CONFIG_CMD_SOURCE "source" command Support CONFIG_CMD_SPI * SPI serial bus support @@ -746,6 +746,10 @@ The following options need to be configured: CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO CONFIG_PCA953X_INFO - enable pca953x info command + The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of + chip-ngpio pairs that tell the PCA953X driver the number of + pins supported by a particular chip. + Note that if the GPIO device uses I2C, then the I2C interface must also be configured. See I2C Support, below. @@ -861,6 +865,18 @@ The following options need to be configured: Define this to use i/o functions instead of macros (some hardware wont work with macros) + CONFIG_FTGMAC100 + Support for Faraday's FTGMAC100 Gigabit SoC Ethernet + + CONFIG_FTGMAC100_EGIGA + Define this to use GE link update with gigabit PHY. + Define this if FTGMAC100 is connected to gigabit PHY. + If your system has 10/100 PHY only, it might not occur + wrong behavior. Because PHY usually return timeout or + useless data when polling gigabit status and gigabit + control registers. This behavior won't affect the + correctnessof 10/100 link speed update. + CONFIG_SMC911X Support for SMSC's LAN911x and LAN921x chips @@ -876,6 +892,18 @@ The following options need to be configured: automatically converts one 32 bit word to two 16 bit words you may also try CONFIG_SMC911X_32_BIT. + CONFIG_SH_ETHER + Support for Renesas on-chip Ethernet controller + + CONFIG_SH_ETHER_USE_PORT + Define the number of ports to be used + + CONFIG_SH_ETHER_PHY_ADDR + Define the ETH PHY's address + + CONFIG_SH_ETHER_CACHE_WRITEBACK + If this option is set, the driver enables cache flush. + - USB Support: At the moment only the UHCI host controller is supported (PIP405, MIP405, MPC5200); define @@ -1632,6 +1660,11 @@ The following options need to be configured: SPI EEPROM, also an instance works with Crystal A/D and D/As on the SACSng board) + CONFIG_SH_SPI + + Enables the driver for SPI controller on SuperH. Currently + only SH7757 is supported. + CONFIG_SPI_X Enables extended (16-bit) SPI EEPROM addressing. @@ -1781,7 +1814,7 @@ The following options need to be configured: ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL, HERMES, IP860, RPXlite, LWMON, LANTEC, - PCU_E, FLAGADM, TQM8260 + FLAGADM, TQM8260 - Error Recovery: CONFIG_PANIC_HANG @@ -2248,7 +2281,7 @@ Configuration Settings: - CONFIG_SYS_MONITOR_BASE: Physical start address of boot monitor code (set by make config files to be same as the text base address - (TEXT_BASE) used when linking) - same as + (CONFIG_SYS_TEXT_BASE) used when linking) - same as CONFIG_SYS_FLASH_BASE when booting from flash. - CONFIG_SYS_MONITOR_LEN: @@ -2275,6 +2308,19 @@ Configuration Settings: all data for the Linux kernel must be between "bootm_low" and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. +- CONFIG_SYS_BOOT_RAMDISK_HIGH: + Enable initrd_high functionality. If defined then the + initrd_high feature is enabled and the bootm ramdisk subcommand + is enabled. + +- CONFIG_SYS_BOOT_GET_CMDLINE: + Enables allocating and saving kernel cmdline in space between + "bootm_low" and "bootm_low" + BOOTMAPSZ. + +- CONFIG_SYS_BOOT_GET_KBD: + Enables allocating and saving a kernel copy of the bd_info in + space between "bootm_low" and "bootm_low" + BOOTMAPSZ. + - CONFIG_SYS_MAX_FLASH_BANKS: Max number of Flash memory banks @@ -2351,11 +2397,11 @@ Configuration Settings: - CONFIG_ENV_MAX_ENTRIES - Maximum number of entries in the hash table that is used - internally to store the environment settings. The default - setting is supposed to be generous and should work in most - cases. This setting can be used to tune behaviour; see - lib/hashtable.c for details. + Maximum number of entries in the hash table that is used + internally to store the environment settings. The default + setting is supposed to be generous and should work in most + cases. This setting can be used to tune behaviour; see + lib/hashtable.c for details. The following definitions that deal with the placement and management of environment data (variable area); in general, we support the @@ -2534,18 +2580,32 @@ to save the current settings. - CONFIG_ENV_SIZE: These two #defines specify the offset and size of the environment - area within the first NAND device. + area within the first NAND device. CONFIG_ENV_OFFSET must be + aligned to an erase block boundary. - - CONFIG_ENV_OFFSET_REDUND + - CONFIG_ENV_OFFSET_REDUND (optional): This setting describes a second storage area of CONFIG_ENV_SIZE - size used to hold a redundant copy of the environment data, - so that there is a valid backup copy in case there is a - power failure during a "saveenv" operation. + size used to hold a redundant copy of the environment data, so + that there is a valid backup copy in case there is a power failure + during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be + aligned to an erase block boundary. + + - CONFIG_ENV_RANGE (optional): + + Specifies the length of the region in which the environment + can be written. This should be a multiple of the NAND device's + block size. Specifying a range with more erase blocks than + are needed to hold CONFIG_ENV_SIZE allows bad blocks within + the range to be avoided. - Note: CONFIG_ENV_OFFSET and CONFIG_ENV_OFFSET_REDUND must be aligned - to a block boundary, and CONFIG_ENV_SIZE must be a multiple of - the NAND devices block size. + - CONFIG_ENV_OFFSET_OOB (optional): + + Enables support for dynamically retrieving the offset of the + environment from block zero's out-of-band data. The + "nand env.oob" command can be used to record this offset. + Currently, CONFIG_ENV_OFFSET_REDUND is not supported when + using CONFIG_ENV_OFFSET_OOB. - CONFIG_NAND_ENV_DST @@ -2659,7 +2719,7 @@ Low Level (hardware related) configuration options: area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial data is located at the end of the available space - (sometimes written as (CONFIG_SYS_INIT_RAM_END - + (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET) downward. @@ -2744,6 +2804,24 @@ Low Level (hardware related) configuration options: Disable PCI-Express on systems where it is supported but not required. +- CONFIG_SYS_SRIO: + Chip has SRIO or not + +- CONFIG_SRIO1: + Board has SRIO 1 port available + +- CONFIG_SRIO2: + Board has SRIO 2 port available + +- CONFIG_SYS_SRIOn_MEM_VIRT: + Virtual Address of SRIO port 'n' memory region + +- CONFIG_SYS_SRIOn_MEM_PHYS: + Physical Address of SRIO port 'n' memory region + +- CONFIG_SYS_SRIOn_MEM_SIZE: + Size of SRIO port 'n' memory region + - CONFIG_SPD_EEPROM Get DDR timing information from an I2C EEPROM. Common with pluggable memory modules such as SODIMMs @@ -2809,19 +2887,17 @@ Low Level (hardware related) configuration options: globally (CONFIG_CMD_MEM). - CONFIG_SKIP_LOWLEVEL_INIT -- CONFIG_SKIP_RELOCATE_UBOOT + [ARM only] If this variable is defined, then certain + low level initializations (like setting up the memory + controller) are omitted and/or U-Boot does not + relocate itself into RAM. - [ARM only] If these variables are defined, then - certain low level initializations (like setting up - the memory controller) are omitted and/or U-Boot does - not relocate itself into RAM. - Normally these variables MUST NOT be defined. The - only exception is when U-Boot is loaded (to RAM) by - some other boot loader or by a debugger which - performs these initializations itself. + Normally this variable MUST NOT be defined. The only + exception is when U-Boot is loaded (to RAM) by some + other boot loader or by a debugger which performs + these initializations itself. - CONFIG_PRELOADER - Modifies the behaviour of start.S when compiling a loader that is executed before the actual U-Boot. E.g. when compiling a NAND SPL.