X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;f=README;h=1bcb63c7e39b8316ca8642dce640f543a5f6b012;hb=300c2e6263b2a21f9710eef7211dbd49c962a77e;hp=c49af7449099af23ad4371a5421ae0dcecb4cf7b;hpb=a128197b815cbef81549434c3591108618ecc7ba;p=oweals%2Fu-boot.git

diff --git a/README b/README
index c49af74490..1bcb63c7e3 100644
--- a/README
+++ b/README
@@ -1671,7 +1671,7 @@ The following options need to be configured:
 		key for the Replay Protection Memory Block partition in eMMC.
 
 - USB Device Firmware Update (DFU) class support:
-		CONFIG_DFU_FUNCTION
+		CONFIG_USB_FUNCTION_DFU
 		This enables the USB portion of the DFU USB class
 
 		CONFIG_CMD_DFU
@@ -1716,6 +1716,9 @@ The following options need to be configured:
 		sending again an USB request to the device.
 
 - USB Device Android Fastboot support:
+		CONFIG_USB_FUNCTION_FASTBOOT
+		This enables the USB part of the fastboot gadget
+
 		CONFIG_CMD_FASTBOOT
 		This enables the command "fastboot" which enables the Android
 		fastboot mode for the platform's USB device. Fastboot is a USB
@@ -1727,12 +1730,12 @@ The following options need to be configured:
 		This enables support for booting images which use the Android
 		image format header.
 
-		CONFIG_USB_FASTBOOT_BUF_ADDR
+		CONFIG_FASTBOOT_BUF_ADDR
 		The fastboot protocol requires a large memory buffer for
 		downloads. Define this to the starting RAM address to use for
 		downloaded images.
 
-		CONFIG_USB_FASTBOOT_BUF_SIZE
+		CONFIG_FASTBOOT_BUF_SIZE
 		The fastboot protocol requires a large memory buffer for
 		downloads. This buffer should be as large as possible for a
 		platform. Define this to the size available RAM for fastboot.
@@ -3079,31 +3082,12 @@ CBFS (Coreboot Filesystem) support
 		Define this option to include a destructive SPI flash
 		test ('sf test').
 
-		CONFIG_SPI_FLASH_BAR		Ban/Extended Addr Reg
-
-		Define this option to use the Bank addr/Extended addr
-		support on SPI flashes which has size > 16Mbytes.
-
 		CONFIG_SF_DUAL_FLASH		Dual flash memories
 
 		Define this option to use dual flash support where two flash
 		memories can be connected with a given cs line.
 		Currently Xilinx Zynq qspi supports these type of connections.
 
-		CONFIG_SPI_FLASH_MTD		spi-flash MTD layer
-
-		Define this option to use mtd support for spi flash layer, this
-		adapter is for translating mtd_read/mtd_write commands into
-		spi_flash_read/spi_flash_write commands. It is not intended to
-		use it within sf_cmd or the SPI flash subsystem. Such an adapter
-		is needed for subsystems like UBI which can only operate on top
-		of the MTD layer.
-
-		CONFIG_SPI_FLASH_DATAFLASH	SPI based Dataflash
-
-		Define this option to access AT45xxx Dataflash chips support
-		using spi flash interface.
-
 - SystemACE Support:
 		CONFIG_SYSTEMACE
 
@@ -5082,6 +5066,33 @@ within that device.
 	normal addressable memory via the LBC. CONFIG_SYS_LS_MC_FW_ADDR is the
 	virtual address in NOR flash.
 
+Freescale Layerscape Debug Server Support:
+-------------------------------------------
+The Freescale Layerscape Debug Server Support supports the loading of
+"Debug Server firmware" and triggering SP boot-rom.
+This firmware often needs to be loaded during U-Boot booting.
+
+- CONFIG_FSL_DEBUG_SERVER
+	Enable the Debug Server for Layerscape SoCs.
+
+- CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE
+	Define minimum DDR size required for debug server image
+
+- CONFIG_SYS_MEM_TOP_HIDE_MIN
+	Define minimum DDR size to be hided from top of the DDR memory
+
+Reproducible builds
+-------------------
+
+In order to achieve reproducible builds, timestamps used in the U-Boot build
+process have to be set to a fixed value.
+
+This is done using the SOURCE_DATE_EPOCH environment variable.
+SOURCE_DATE_EPOCH is to be set on the build host's shell, not as a configuration
+option for U-Boot or an environment variable in U-Boot.
+
+SOURCE_DATE_EPOCH should be set to a number of seconds since the epoch, in UTC.
+
 Building the Software:
 ======================