X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;ds=sidebyside;f=drivers%2Fmmc%2FKconfig;h=0a0d4aaf6ca0d4438fd184261108ee5aceaf1839;hb=0223462b373b975d970fa86e5e1a7eadd1d41820;hp=6de927b8c6cb98ee71c60b8b6e22ec8ae3a7ffa7;hpb=1d20170467b079642be96996dcd71db64c3c365c;p=oweals%2Fu-boot.git diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig index 6de927b8c6..0a0d4aaf6c 100644 --- a/drivers/mmc/Kconfig +++ b/drivers/mmc/Kconfig @@ -3,6 +3,7 @@ menu "MMC Host controller Support" config MMC bool "MMC/SD/SDIO card support" default ARM || PPC || SANDBOX + select HAVE_BLOCK_DEVICE help This selects MultiMediaCard, Secure Digital and Secure Digital I/O support. @@ -10,6 +11,18 @@ config MMC If you want MMC/SD/SDIO support, you should say Y here and also to your specific host controller driver. +config MMC_WRITE + bool "support for MMC/SD write operations" + depends on MMC + default y + help + Enable write access to MMC and SD Cards + +config MMC_BROKEN_CD + bool "Poll for broken card detection case" + help + If card detection feature is broken, just poll to detect. + config DM_MMC bool "Enable MMC controllers using Driver Model" depends on DM @@ -33,6 +46,112 @@ config SPL_DM_MMC if MMC +config ARM_PL180_MMCI + bool "ARM AMBA Multimedia Card Interface and compatible support" + depends on DM_MMC && OF_CONTROL + help + This selects the ARM(R) AMBA(R) PrimeCell Multimedia Card + Interface (PL180, PL181 and compatible) support. + If you have an ARM(R) platform with a Multimedia Card slot, + say Y or M here. + +config MMC_QUIRKS + bool "Enable quirks" + default y + help + Some cards and hosts may sometimes behave unexpectedly (quirks). + This option enable workarounds to handle those quirks. Some of them + are enabled by default, other may require additionnal flags or are + enabled by the host driver. + +config MMC_HW_PARTITIONING + bool "Support for HW partitioning command(eMMC)" + default y + help + This adds a command and an API to do hardware partitioning on eMMC + devices. + +config SUPPORT_EMMC_RPMB + bool "Support eMMC replay protected memory block (RPMB)" + imply CMD_MMC_RPMB + help + Enable support for reading, writing and programming the + key for the Replay Protection Memory Block partition in eMMC. + +config MMC_IO_VOLTAGE + bool "Support IO voltage configuration" + help + IO voltage configuration allows selecting the voltage level of the IO + lines (not the level of main supply). This is required for UHS + support. For eMMC this not mandatory, but not enabling this option may + prevent the driver of using the faster modes. + +config SPL_MMC_IO_VOLTAGE + bool "Support IO voltage configuration in SPL" + default n + help + IO voltage configuration allows selecting the voltage level of the IO + lines (not the level of main supply). This is required for UHS + support. For eMMC this not mandatory, but not enabling this option may + prevent the driver of using the faster modes. + +config MMC_UHS_SUPPORT + bool "enable UHS support" + depends on MMC_IO_VOLTAGE + help + The Ultra High Speed (UHS) bus is available on some SDHC and SDXC + cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus + frequency can go up to 208MHz (SDR104) + +config SPL_MMC_UHS_SUPPORT + bool "enable UHS support in SPL" + depends on SPL_MMC_IO_VOLTAGE + help + The Ultra High Speed (UHS) bus is available on some SDHC and SDXC + cards. The IO voltage must be switchable from 3.3v to 1.8v. The bus + frequency can go up to 208MHz (SDR104) + +config MMC_HS400_SUPPORT + bool "enable HS400 support" + select MMC_HS200_SUPPORT + help + The HS400 mode is support by some eMMC. The bus frequency is up to + 200MHz. This mode requires tuning the IO. + +config SPL_MMC_HS400_SUPPORT + bool "enable HS400 support in SPL" + help + The HS400 mode is support by some eMMC. The bus frequency is up to + 200MHz. This mode requires tuning the IO. + +config MMC_HS200_SUPPORT + bool "enable HS200 support" + help + The HS200 mode is support by some eMMC. The bus frequency is up to + 200MHz. This mode requires tuning the IO. + + +config SPL_MMC_HS200_SUPPORT + bool "enable HS200 support in SPL" + help + The HS200 mode is support by some eMMC. The bus frequency is up to + 200MHz. This mode requires tuning the IO. + +config MMC_VERBOSE + bool "Output more information about the MMC" + default y + help + Enable the output of more information about the card such as the + operating mode. + +config MMC_TRACE + bool "MMC debugging" + default n + help + This is an option for use by developer. Enable MMC core debugging. + + If you need to see the MMC core message, say Y. + config SPL_MMC_TINY bool "Tiny MMC framework in SPL" help @@ -119,6 +238,10 @@ config MMC_MXC config MMC_MXS bool "Freescale MXS Multimedia Card Interface support" + depends on MX23 || MX28 || MX6 || MX7 + select APBH_DMA + select APBH_DMA_BURST if ARCH_MX6 || ARCH_MX7 + select APBH_DMA_BURST8 if ARCH_MX6 || ARCH_MX7 help This selects the Freescale SSP MMC controller found on MXS based platforms like mx23/28. @@ -136,6 +259,7 @@ config MMC_PCI config MMC_OMAP_HS bool "TI OMAP High Speed Multimedia Card Interface support" select DM_REGULATOR_PBIAS if DM_MMC && DM_REGULATOR + select DM_REGULATOR_PBIAS if DM_MMC && DM_REGULATOR help This selects the TI OMAP High Speed Multimedia card Interface. If you have an omap2plus board with a Multimedia Card slot, @@ -143,6 +267,15 @@ config MMC_OMAP_HS If unsure, say N. +config MMC_OMAP_HS_ADMA + bool "ADMA support for OMAP HS MMC" + depends on MMC_OMAP_HS && !OMAP34XX + default y if !AM33XX + help + This enables support for the ADMA2 controller (SDA3.00 Part A2 DMA + controller). If supported by the hardware, selecting this option will + increase performances. + config MMC_OMAP36XX_PINS bool "Enable MMC1 on OMAP36xx/37xx" depends on OMAP34XX && MMC_OMAP_HS @@ -161,13 +294,43 @@ config SH_SDHI help Support for the on-chip SDHI host controller on SuperH/Renesas ARM SoCs platform +config SH_MMCIF + bool "SuperH/Renesas ARM SoCs on-chip MMCIF host controller support" + depends on ARCH_RMOBILE || SH + help + Support for the on-chip MMCIF host controller on SuperH/Renesas ARM SoCs platform + config MMC_UNIPHIER bool "UniPhier SD/MMC Host Controller support" depends on ARCH_UNIPHIER depends on BLK && DM_MMC depends on OF_CONTROL help - This selects support for the SD/MMC Host Controller on UniPhier SoCs. + This selects support for the Matsushita SD/MMC Host Controller on + SocioNext UniPhier SoCs. + +config RENESAS_SDHI + bool "Renesas R-Car SD/MMC Host Controller support" + depends on ARCH_RMOBILE + depends on BLK && DM_MMC + depends on OF_CONTROL + help + This selects support for the Matsushita SD/MMC Host Controller on + Renesas R-Car SoCs. + +config MMC_BCM2835 + bool "BCM2835 family custom SD/MMC Host Controller support" + depends on ARCH_BCM283X + depends on BLK && DM_MMC + depends on OF_CONTROL + default y + help + This selects support for the custom SD host controller in the BCM2835 + family of devices. + + If you have a BCM2835 platform with SD or MMC devices, say Y here. + + If unsure, say N. config MMC_SANDBOX bool "Sandbox MMC support" @@ -229,6 +392,17 @@ config MMC_SDHCI_BCM2835 If unsure, say N. +config MMC_SDHCI_BCMSTB + tristate "SDHCI support for the BCMSTB SD/MMC Controller" + depends on MMC_SDHCI + help + This selects the Broadcom set-top box SD/MMC controller. + + If you have a BCMSTB platform with SD or MMC devices, + say Y here. + + If unsure, say N. + config MMC_SDHCI_CADENCE bool "SDHCI support for the Cadence SD/SDIO/eMMC controller" depends on BLK && DM_MMC @@ -241,6 +415,15 @@ config MMC_SDHCI_CADENCE If unsure, say N. +config MMC_SDHCI_K3_ARASAN + bool "Arasan SDHCI controller for TI's K3 based SoCs" + depends on ARCH_K3 + depends on MMC_SDHCI + depends on DM_MMC && OF_CONTROL && BLK + help + Support for Arasan SDHCI host controller on Texas Instruments' + K3 family based SoC platforms + config MMC_SDHCI_KONA bool "SDHCI support on Broadcom KONA platform" depends on MMC_SDHCI @@ -361,6 +544,19 @@ config MMC_SDHCI_ZYNQ help Support for Arasan SDHCI host controller on Zynq/ZynqMP ARM SoCs platform +config ZYNQ_SDHCI_MAX_FREQ + int "Set the maximum frequency of the controller" + depends on MMC_SDHCI_ZYNQ + help + Set the maximum frequency of the controller. + +config ZYNQ_SDHCI_MIN_FREQ + int "Set the minimum frequency of the controller" + depends on MMC_SDHCI_ZYNQ + default 0 + help + Set the minimum frequency of the controller. + config MMC_SUNXI bool "Allwinner sunxi SD/MMC Host Controller support" depends on ARCH_SUNXI && !UART0_PORT_F @@ -382,6 +578,26 @@ config GENERIC_ATMEL_MCI the SD Memory Card Specification V2.0, the SDIO V2.0 specification and CE-ATA V1.1. +config STM32_SDMMC2 + bool "STMicroelectronics STM32H7 SD/MMC Host Controller support" + depends on DM_MMC && BLK && OF_CONTROL + help + This selects support for the SD/MMC controller on STM32H7 SoCs. + If you have a board based on such a SoC and with a SD/MMC slot, + say Y or M here. + +config FTSDC010 + bool "Ftsdc010 SD/MMC controller Support" + help + This SD/MMC controller is present in Andestech SoCs which is based on Faraday IP. + +config FTSDC010_SDIO + bool "Support ftsdc010 sdio" + default n + depends on FTSDC010 + help + This can enable ftsdc010 sdio function. + endif config TEGRA124_MMC_DISABLE_EXT_LOOPBACK @@ -395,6 +611,12 @@ config TEGRA124_MMC_DISABLE_EXT_LOOPBACK TODO(marcel.ziswiler@toradex.com): Move to device tree controlled approach once proper kernel integration made it mainline. +config FSL_ESDHC + bool "Freescale/NXP eSDHC controller support" + help + This selects support for the eSDHC (enhanced secure digital host + controller) found on numerous Freescale/NXP SoCs. + endmenu config SYS_FSL_ERRATUM_ESDHC111