X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;ds=sidebyside;f=README;h=677c3dc252174f62dacc13bb93ab4aad702e63a6;hb=31043e20ae748635f142483e8b7b645948687055;hp=78aa5a518031e47c917b85ca3ebb65cc9325d823;hpb=9ed887caecb9ecb0c68773a1870d143b9f28d3da;p=oweals%2Fu-boot.git

diff --git a/README b/README
index 78aa5a5180..677c3dc252 100644
--- a/README
+++ b/README
@@ -406,13 +406,25 @@ The following options need to be configured:
 		This is the value to write into CCSR offset 0x18600
 		according to the A004510 workaround.
 
+		CONFIG_SYS_FSL_DSP_DDR_ADDR
+		This value denotes start offset of DDR memory which is
+		connected exclusively to the DSP cores.
+
 		CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
 		This value denotes start offset of M2 memory
 		which is directly connected to the DSP core.
 
+		CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
+		This value denotes start offset of M3 memory which is directly
+		connected to the DSP core.
+
 		CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
 		This value denotes start offset of DSP CCSR space.
 
+		CONFIG_SYS_FSL_DDR_EMU
+		Specify emulator support for DDR. Some DDR features such as
+		deskew training are not available.
+
 - Generic CPU options:
 		CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
 
@@ -3078,6 +3090,14 @@ FIT uImage format:
 		Support for NAND boot using simple NAND drivers that
 		expose the cmd_ctrl() interface.
 
+		CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+		Set for the SPL on PPC mpc8xxx targets, support for
+		arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary.
+
+		CONFIG_SPL_COMMON_INIT_DDR
+		Set for common ddr init with serial presence detect in
+		SPL binary.
+
 		CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
 		CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
 		CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
@@ -3147,6 +3167,17 @@ FIT uImage format:
 		option to re-enable it. This will affect the output of the
 		bootm command when booting a FIT image.
 
+- TPL framework
+		CONFIG_TPL
+		Enable building of TPL globally.
+
+		CONFIG_TPL_PAD_TO
+		Image offset to which the TPL should be padded before appending
+		the TPL payload. By default, this is defined as
+                CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
+                CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
+                payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
+
 Modem Support:
 --------------
 
@@ -4184,6 +4215,11 @@ Low Level (hardware related) configuration options:
 		that is executed before the actual U-Boot. E.g. when
 		compiling a NAND SPL.
 
+- CONFIG_TPL_BUILD
+		Modifies the behaviour of start.S  when compiling a loader
+		that is executed after the SPL and before the actual U-Boot.
+		It is loaded by the SPL.
+
 - CONFIG_SYS_MPC85XX_NO_RESETVEC
 		Only for 85xx systems. If this variable is specified, the section
 		.resetvec is not kept and the section .bootpg is placed in the
@@ -4630,6 +4666,12 @@ List of environment variables (most likely not complete):
 
   npe_ucode	- set load address for the NPE microcode
 
+  silent_linux  - If set then linux will be told to boot silently, by
+		  changing the console to be empty. If "yes" it will be
+		  made silent. If "no" it will not be made silent. If
+		  unset, then it will be made silent if the U-Boot console
+		  is silent.
+
   tftpsrcport	- If this is set, the value is used for TFTP's
 		  UDP source port.