X-Git-Url: https://git.librecmc.org/?a=blobdiff_plain;ds=inline;f=doc%2FREADME.rockchip;h=d17afeabdd2c646720bdfc483a1f92753a152b43;hb=a8973731a452323e8767e8f9775c7d06921ebed5;hp=51b00a9d8505f9cf4d06b1faf8f39229174d0805;hpb=760b95789e0604fe62ce280674f82a3778b36c9a;p=oweals%2Fu-boot.git diff --git a/doc/README.rockchip b/doc/README.rockchip index 51b00a9d85..d17afeabdd 100644 --- a/doc/README.rockchip +++ b/doc/README.rockchip @@ -6,13 +6,7 @@ U-Boot on Rockchip ================== -There are several repositories available with versions of U-Boot that support -many Rockchip devices [1] [2]. - -The current mainline support is experimental only and is not useful for -anything. It should provide a base on which to build. - -So far only support for the RK3288 and RK3036 is provided. +A wide range of Rockchip SoCs are supported in mainline U-Boot Prerequisites @@ -34,29 +28,149 @@ You will need: Building ======== -At present nine RK3288 boards are supported: +At present 11 RK3288 boards are supported: - EVB RK3288 - use evb-rk3288 configuration - - Fennec RK3288 - use fennec-rk3288 configuration - Firefly RK3288 - use firefly-rk3288 configuration - Hisense Chromebook - use chromebook_jerry configuration + - Asus C100P Chromebook - use chromebook_minnie configuration + - Asus Chromebit - use chromebook_mickey configuration - MiQi RK3288 - use miqi-rk3288 configuration - phyCORE-RK3288 RDK - use phycore-rk3288 configuration - PopMetal RK3288 - use popmetal-rk3288 configuration - Radxa Rock 2 - use rock2 configuration - Tinker RK3288 - use tinker-rk3288 configuration + - Vyasa RK3288 - use vyasa-rk3288 configuration -Two RK3036 board are supported: +Two RK3036 boards are supported: - EVB RK3036 - use evb-rk3036 configuration - Kylin - use kylin_rk3036 configuration +Two RK3328 board are supported: + + - EVB RK3328 - use evb-rk3328_defconfig + - Pine64 Rock64 board - use rock64-rk3328_defconfig + +Size RK3399 boards are supported (aarch64): + + - EBV RK3399 - use evb_rk3399 configuration + - Firefly RK3399 - use the firefly_rk3399 configuration + - Puma - use puma_rk3399 configuration + - Ficus - use ficus-rk3399 configuration + - Rock960 (Vamrs) - use rock960-rk3399 configuration + - Bob - use chromebook_bob configuration + +Four RK3368 boards are supported: + + - Sheep - use sheep-rk3368 configuration + - Lion - use lion-rk3368 configuration + - Geekbox - use geekbox configuration + - EVB PX5 - use evb-px5 configuration + +One RK3128 board is supported: + + - EVB RK3128 - use evb-rk3128 configuration + +One RK3229 board is supported: + + - EVB RK3229 - use evb-rk3229 configuration + +Two RV1108 boards are supported: + + - EVB RV1108 - use evb-rv1108 configuration + - Elgin R1 - use elgin-rv1108 configuration + +One RV3188 baord is supported: + + - Raxda Rock - use rock configuration + + For example: +1. To build RK3288 board: + CROSS_COMPILE=arm-linux-gnueabi- make O=firefly firefly-rk3288_defconfig all -(or you can use another cross compiler if you prefer) + (or you can use another cross compiler if you prefer) + +2. To build RK3399 board: + + Option 1: Package the image with Rockchip miniloader: + + - Compile U-Boot + + => cd /path/to/u-boot + => make nanopi-neo4-rk3399_defconfig + => make + + - Get the rkbin + + => git clone https://github.com/rockchip-linux/rkbin.git + + - Create trust.img + + => cd /path/to/rkbin + => ./tools/trust_merger RKTRUST/RK3399TRUST.ini + + - Create uboot.img + + => cd /path/to/rkbin + => ./tools/loaderimage --pack --uboot /path/to/u-boot/u-boot-dtb.bin uboot.img + + (Get trust.img and uboot.img) + + Option 2: Package the image with SPL: + + - Export cross compiler path for aarch64 + + - Compile ATF + + For Puma board. + + => git clone git://git.theobroma-systems.com/arm-trusted-firmware.git + => cd arm-trusted-firmware + => make CROSS_COMPILE=aarch64-linux-gnu- PLAT=rk3399 bl31 + + (export bl31.bin) + => export BL31=/path/to/arm-trusted-firmware/build/rk3399/release/bl31/bl31.bin + + For rest of rk3399 boards. + + => git clone https://github.com/ARM-software/arm-trusted-firmware.git + => cd arm-trusted-firmware + + (export cross compiler path for Cortex-M0 MCU likely arm-none-eabi-) + => make realclean + => make CROSS_COMPILE=aarch64-linux-gnu- PLAT=rk3399 + + (export bl31.elf) + => export BL31=/path/to/arm-trusted-firmware/build/rk3399/release/bl31/bl31.elf + + - Compile PMU M0 firmware + + This is optional for most of the rk3399 boards and required only for Puma board. + + => git clone git://git.theobroma-systems.com/rk3399-cortex-m0.git + => cd rk3399-cortex-m0 + + (export cross compiler path for Cortex-M0 PMU) + => make CROSS_COMPILE=arm-cortex_m0-eabi- + + (export rk3399m0.bin) + => export PMUM0=/path/to/rk3399-cortex-m0/rk3399m0.bin + + - Compile U-Boot + => cd /path/to/u-boot + => make orangepi-rk3399_defconfig + => make + + (Get spl/u-boot-spl-dtb.bin, u-boot.itb images and some boards would get + spl/u-boot-spl.bin since it doesn't enable CONFIG_SPL_OF_CONTROL + + If TPL enabled on the target, get tpl/u-boot-tpl-dtb.bin or tpl/u-boot-tpl.bin + if CONFIG_TPL_OF_CONTROL not enabled) Writing to the board with USB ============================= @@ -161,9 +275,7 @@ As of now TPL is added on Vyasa-RK3288 board. To write an image that boots from an SD card (assumed to be /dev/mmcblk0): - ./tools/mkimage -n rk3288 -T rksd -d ./tpl/u-boot-tpl.bin out && - cat ./spl/u-boot-spl-dtb.bin >> out && - sudo dd if=out of=/dev/mmcblk0 seek=64 && + sudo dd if=idbloader.img of=/dev/mmcblk0 seek=64 && sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 seek=16384 Booting from an SD card on RK3188 @@ -190,6 +302,203 @@ tools/mkimage -n rk3188 -T rksd -d spl/u-boot-spl.bin out truncate -s %2048 u-boot.bin cat u-boot.bin | split -b 512 --filter='openssl rc4 -K 7C4E0304550509072D2C7B38170D1711' >> out +Booting from an SD card on Pine64 Rock64 (RK3328) +================================================= + +For Rock64 rk3328 board the following three parts are required: +TPL, SPL, and the u-boot image tree blob. + + - Write TPL/SPL image at 64 sector + + => sudo dd if=idbloader.img of=/dev/mmcblk0 seek=64 + + - Write u-boot image tree blob at 16384 sector + + => sudo dd if=u-boot.itb of=/dev/mmcblk0 seek=16384 + +Booting from an SD card on RK3399 +================================= + +To write an image that boots from an SD card (assumed to be /dev/sdc): + +Option 1: Package the image with Rockchip miniloader: + + - Create idbloader.img + + => cd /path/to/u-boot + => ./tools/mkimage -n rk3399 -T rksd -d /path/to/rkbin/bin/rk33/rk3399_ddr_800MHz_v1.20.bin idbloader.img + => cat /path/to/rkbin/bin/rk33/rk3399_miniloader_v1.19.bin >> idbloader.img + + - Write idbloader.img at 64 sector + + => sudo dd if=idbloader.img of=/dev/sdc seek=64 + + - Write trust.img at 24576 + + => sudo dd if=trust.img of=/dev/sdc seek=24576 + + - Write uboot.img at 16384 sector + + => sudo dd if=uboot.img of=/dev/sdc seek=16384 + => sync + +Put this SD (or micro-SD) card into your board and reset it. You should see +something like: + +DDR Version 1.20 20190314 +In +Channel 0: DDR3, 933MHz +Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB +no stride +ch 0 ddrconfig = 0x101, ddrsize = 0x20 +pmugrf_os_reg[2] = 0x10006281, stride = 0x17 +OUT +Boot1: 2019-03-14, version: 1.19 +CPUId = 0x0 +ChipType = 0x10, 239 +mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 +mmc: ERROR: Card did not respond to voltage select! +emmc reinit +mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 +mmc: ERROR: Card did not respond to voltage select! +emmc reinit +mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000 +mmc: ERROR: Card did not respond to voltage select! +SdmmcInit=2 1 +mmc0:cmd5,20 +SdmmcInit=0 0 +BootCapSize=0 +UserCapSize=60543MB +FwPartOffset=2000 , 0 +StorageInit ok = 45266 +SecureMode = 0 +SecureInit read PBA: 0x4 +SecureInit read PBA: 0x404 +SecureInit read PBA: 0x804 +SecureInit read PBA: 0xc04 +SecureInit read PBA: 0x1004 +SecureInit read PBA: 0x1404 +SecureInit read PBA: 0x1804 +SecureInit read PBA: 0x1c04 +SecureInit ret = 0, SecureMode = 0 +atags_set_bootdev: ret:(0) +GPT 0x3380ec0 signature is wrong +recovery gpt... +GPT 0x3380ec0 signature is wrong +recovery gpt fail! +LoadTrust Addr:0x4000 +No find bl30.bin +Load uboot, ReadLba = 2000 +hdr 0000000003380880 + 0x0:0x88,0x41,0x3e,0x97,0xe6,0x61,0x54,0x23,0xe9,0x5a,0xd1,0x2b,0xdc,0x2f,0xf9,0x35, + +Load OK, addr=0x200000, size=0x9c9c0 +RunBL31 0x10000 +NOTICE: BL31: v1.3(debug):370ab80 +NOTICE: BL31: Built : 09:23:41, Mar 4 2019 +NOTICE: BL31: Rockchip release version: v1.1 +INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3 +INFO: Using opteed sec cpu_context! +INFO: boot cpu mask: 0 +INFO: plat_rockchip_pmu_init(1181): pd status 3e +INFO: BL31: Initializing runtime services +INFO: BL31: Initializing BL32 +INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-195-g8f090d20 #6 Fri Dec 7 06:11:20 UTC 2018 aarch64) + +INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2 + +INF [0x0] TEE-CORE:init_teecore:83: teecore inits done +INFO: BL31: Preparing for EL3 exit to normal world +INFO: Entry point address = 0x200000 +INFO: SPSR = 0x3c9 + + +U-Boot 2019.04-rc4-00136-gfd121f9641-dirty (Apr 16 2019 - 14:02:47 +0530) + +Model: FriendlyARM NanoPi NEO4 +DRAM: 1022 MiB +MMC: dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0 +Loading Environment from MMC... *** Warning - bad CRC, using default environment + +In: serial@ff1a0000 +Out: serial@ff1a0000 +Err: serial@ff1a0000 +Model: FriendlyARM NanoPi NEO4 +Net: eth0: ethernet@fe300000 +Hit any key to stop autoboot: 0 +=> + +Option 2: Package the image with SPL: + + - Prefix rk3399 header to SPL image + + => cd /path/to/u-boot + => ./tools/mkimage -n rk3399 -T rksd -d spl/u-boot-spl-dtb.bin out + + - Write prefixed SPL at 64th sector + + => sudo dd if=out of=/dev/sdc seek=64 + + - Write U-Boot proper at 16384 sector + + => sudo dd if=u-boot.itb of=/dev/sdc seek=16384 + => sync + +Put this SD (or micro-SD) card into your board and reset it. You should see +something like: + +U-Boot SPL board init +Trying to boot from MMC1 + + +U-Boot 2019.01-00004-g14db5ee998 (Mar 11 2019 - 13:18:41 +0530) + +Model: Orange Pi RK3399 Board +DRAM: 2 GiB +MMC: dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0 +Loading Environment from MMC... OK +In: serial@ff1a0000 +Out: serial@ff1a0000 +Err: serial@ff1a0000 +Model: Orange Pi RK3399 Board +Net: eth0: ethernet@fe300000 +Hit any key to stop autoboot: 0 +=> + +Option 3: Package the image with TPL: + + - Write tpl+spl at 64th sector + + => sudo dd if=idbloader.img of=/dev/sdc seek=64 + + - Write U-Boot proper at 16384 sector + + => sudo dd if=u-boot.itb of=/dev/sdc seek=16384 + => sync + +Put this SD (or micro-SD) card into your board and reset it. You should see +something like: + +U-Boot TPL board init +Trying to boot from BOOTROM +Returning to boot ROM... + +U-Boot SPL board init +Trying to boot from MMC1 + + +U-Boot 2019.07-rc1-00241-g5b3244767a (May 08 2019 - 10:51:06 +0530) + +Model: Orange Pi RK3399 Board +DRAM: 2 GiB +MMC: dwmmc@fe310000: 2, dwmmc@fe320000: 1, sdhci@fe330000: 0 +Loading Environment from MMC... OK +In: serial@ff1a0000 +Out: serial@ff1a0000 +Err: serial@ff1a0000 +Model: Orange Pi RK3399 Board +Net: eth0: ethernet@fe300000 +Hit any key to stop autoboot: 0 +=> Using fastboot on rk3288 ======================== @@ -219,7 +528,8 @@ You should see something like: Booting from SPI ================ -To write an image that boots from SPI flash (e.g. for the Haier Chromebook): +To write an image that boots from SPI flash (e.g. for the Haier Chromebook or +Bob): ./chromebook_jerry/tools/mkimage -n rk3288 -T rkspi \ -d chromebook_jerry/spl/u-boot-spl-dtb.bin spl.bin && \ @@ -228,11 +538,11 @@ To write an image that boots from SPI flash (e.g. for the Haier Chromebook): dd if=out.bin of=out.bin.pad bs=4M conv=sync This converts the SPL image to the required SPI format by adding the Rockchip -header and skipping every 2KB block. Then the U-Boot image is written at +header and skipping every second 2KB block. Then the U-Boot image is written at offset 128KB and the whole image is padded to 4MB which is the SPI flash size. The position of U-Boot is controlled with this setting in U-Boot: - #define CONFIG_SYS_SPI_U_BOOT_OFFS (128 << 10) + #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 If you have a Dediprog em100pro connected then you can write the image with: @@ -264,7 +574,6 @@ Immediate priorities are: - USB device - Run CPU at full speed (code exists but we only see ~60 DMIPS maximum) - NAND flash -- Support for other Rockchip parts - Boot U-Boot proper over USB OTG (at present only SPL works) @@ -350,5 +659,7 @@ There are some documents about partitions in the links below. http://rockchip.wikidot.com/partitions -- +Jagan Teki +27 Mar 2019 Simon Glass 24 June 2015