// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include "qca9557.dtsi"
+#include "qca955x.dtsi"
/ {
chosen {
};
aliases {
- led-status = &system;
+ led-boot = &led_system;
+ led-failsafe = &led_system;
+ led-running = &led_system;
+ led-upgrade = &led_system;
+ label-mac-device = &wmac;
};
leds {
compatible = "gpio-leds";
- system: system {
+ led_system: system {
label = "tp-link:green:system";
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
usb {
label = "tp-link:green:usb";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
- default-state = "off";
trigger-sources = <&hub_port0>;
linux,default-trigger = "usbport";
};
wifi_green {
label = "tp-link:green:wlan";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
- default-state = "off";
linux,default-trigger = "phy0tpt";
};
wifi_wps {
label = "tp-link:green:wps";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
- default-state = "off";
};
};
keys {
compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
reset {
label = "Reset button";
};
&usb0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
status = "okay";
hub_port0: port@1 {
num-cs = <1>;
flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
};
partition@20000 {
+ compatible = "tplink,firmware";
label = "firmware";
reg = <0x020000 0x7d0000>;
};
phy0: ethernet-phy@0 {
reg = <0>;
qca,ar8327-initvals = <
- 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
- 0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
- 0x10 0x81000080 /* POWER_ON_STRIP */
- 0x50 0xcc35cc35 /* LED_CTRL0 */
- 0x54 0xca35ca35 /* LED_CTRL1 */
- 0x58 0xc935c935 /* LED_CTRL2 */
- 0x5c 0x03ffff00 /* LED_CTRL3 */
- 0x7c 0x0000007e /* PORT0_STATUS */
- 0x94 0x0000007e /* PORT6 STATUS */
+ 0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+ 0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
+ 0x10 0x81000080 /* POWER_ON_STRIP */
+ 0x50 0xcc35cc35 /* LED_CTRL0 */
+ 0x54 0xca35ca35 /* LED_CTRL1 */
+ 0x58 0xc935c935 /* LED_CTRL2 */
+ 0x5c 0x03ffff00 /* LED_CTRL3 */
+ 0x7c 0x0000007e /* PORT0_STATUS */
+ 0x94 0x0000007e /* PORT6 STATUS */
>;
};
};
ð0 {
status = "okay";
+ pll-data = <0x56000000 0x00000101 0x00001616>;
+
mtd-mac-address = <&uboot 0x1fc00>;
mtd-mac-address-increment = <1>;
phy-handle = <&phy0>;
ð1 {
status = "okay";
+ pll-data = <0x03000101 0x00000101 0x00001616>;
+
mtd-mac-address = <&uboot 0x1fc00>;
fixed-link {