+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Common SPI Interface: Controller-specific definitions
*
* (C) Copyright 2001
* Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _SPI_H_
#define _SPI_H_
+#include <common.h>
+
/* SPI mode flags */
#define SPI_CPHA BIT(0) /* clock phase */
#define SPI_CPOL BIT(1) /* clock polarity */
#define SPI_XFER_MMAP_END BIT(3) /* Memory Mapped End */
};
-/**
- * Initialization, must be called once on start up.
- *
- * TODO: I don't think we really need this.
- */
-void spi_init(void);
-
/**
* spi_do_alloc_slave - Allocate a new SPI slave (internal)
*
int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
void *din, unsigned long flags);
+/**
+ * spi_write_then_read - SPI synchronous write followed by read
+ *
+ * This performs a half duplex transaction in which the first transaction
+ * is to send the opcode and if the length of buf is non-zero then it start
+ * the second transaction as tx or rx based on the need from respective slave.
+ *
+ * @slave: The SPI slave device with which opcode/data will be exchanged
+ * @opcode: opcode used for specific transfer
+ * @n_opcode: size of opcode, in bytes
+ * @txbuf: buffer into which data to be written
+ * @rxbuf: buffer into which data will be read
+ * @n_buf: size of buf (whether it's [tx|rx]buf), in bytes
+ *
+ * Returns: 0 on success, not 0 on failure
+ */
+int spi_write_then_read(struct spi_slave *slave, const u8 *opcode,
+ size_t n_opcode, const u8 *txbuf, u8 *rxbuf,
+ size_t n_buf);
+
/* Copy memory mapped data */
void spi_flash_copy_mmap(void *data, void *offset, size_t len);
int (*xfer)(struct udevice *dev, unsigned int bitlen, const void *dout,
void *din, unsigned long flags);
+ /**
+ * Optimized handlers for SPI memory-like operations.
+ *
+ * Optimized/dedicated operations for interactions with SPI memory. This
+ * field is optional and should only be implemented if the controller
+ * has native support for memory like operations.
+ */
+ const struct spi_controller_mem_ops *mem_ops;
+
/**
* Set transfer speed.
* This sets a new speed to be applied for next spi_xfer().
* device and slave device.
*
* If no such slave exists, and drv_name is not NULL, then a new slave device
- * is automatically bound on this chip select.
+ * is automatically bound on this chip select with requested speed and mode.
*
- * Ths new slave device is probed ready for use with the given speed and mode.
+ * Ths new slave device is probed ready for use with the speed and mode
+ * from platdata when available or the requested values.
*
* @busnum: SPI bus number
* @cs: Chip select to look for
- * @speed: SPI speed to use for this slave
- * @mode: SPI mode to use for this slave
+ * @speed: SPI speed to use for this slave when not available in platdata
+ * @mode: SPI mode to use for this slave when not available in platdata
* @drv_name: Name of driver to attach to this chip select
* @dev_name: Name of the new device thus created
* @busp: Returns bus device