#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * If we are developing, we might want to start armboot from ram
- * so we MUST NOT initialize critical regs like mem-timing ...
- */
-#define CONFIG_INIT_CRITICAL /* undef for developing */
-
/* High Level Configuration Options */
#define CONFIG_PXA250 1 /* This is an PXA250 CPU */
#define CONFIG_XSENGINE 1
#define CONFIG_MMC 1
-#define BOARD_POST_INIT 1
+#define CONFIG_DOS_PARTITION 1
+#define BOARD_LATE_INIT 1
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
#define PHYS_FLASH_2 0x00000000 /* Flash Bank #2 */
#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 127 KB sectors */
#define CFG_FLASH_BASE PHYS_FLASH_1
-#define CFG_JFFS2_NUM_BANKS 1
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS_CUSTOM_PART 1
+
+/*
+ * JFFS2 partitions
+ */
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=xsengine-0"
+#define MTDPARTS_DEFAULT "mtdparts=xsengine-0:256k(uboot),1m(kernel1),8m(kernel2)"
+*/
/* Environment settings */
#define CONFIG_ENV_OVERWRITE
#define CFG_ENV_SIZE 0x4000 /* 16kB Total Size of Environment Sector */
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (75*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (50*CFG_HZ) /* Timeout for Flash Write */
+#define CFG_FLASH_ERASE_TOUT (75*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT (50*CFG_HZ) /* Timeout for Flash Write */
/* Size of malloc() pool */
#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 256*1024)
/* Hardware drivers */
#define CONFIG_DRIVER_SMC91111
#define CONFIG_SMC91111_BASE 0x04000300
-#define CONFIG_SMC_USE_32_BIT 1
+#define CONFIG_SMC_USE_32_BIT 1
/* select serial console configuration */
#define CONFIG_FFUART 1
/* allow to overwrite serial and ethaddr */
#define CONFIG_BAUDRATE 115200
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MMC | CFG_CMD_FAT | CFG_CMD_PING | CFG_CMD_JFFS2)
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_JFFS2
+
#define CONFIG_BOOTDELAY 3
#define CONFIG_ETHADDR FF:FF:FF:FF:FF:FF
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "XS-Engine u-boot> " /* Monitor Command Prompt */
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0xA0400000 /* memtest works on */
#define CFG_MEMTEST_END 0xA0800000 /* 4 ... 8 MB in DRAM */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* valid baudrates */
#define CFG_MMC_BASE 0xF0000000
-#define CFG_LOAD_ADDR 0xA0000000 /* load kernel to this address */
+#define CFG_LOAD_ADDR 0xA0000000 /* load kernel to this address */
/* Stack sizes - The stack sizes are set up in start.S using the settings below */
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
/* GP direction register */
#define CFG_GPDR0_VAL 0x0000A000 /* CS1, PROG(FPGA) */
#define CFG_GPDR1_VAL 0x00022A80 /* nPWE, FFUART + BTUART pins */
-#define CFG_GPDR2_VAL 0x0000C000 /* CS2, CS3 */
+#define CFG_GPDR2_VAL 0x0000C000 /* CS2, CS3 */
/* GP rising edge detect register */
#define CFG_GRER0_VAL 0x00000000
#define CFG_GAFR0_U_VAL 0x00000010 /* RDY */
#define CFG_GAFR1_L_VAL 0x09988050 /* FFUART + BTUART pins */
#define CFG_GAFR1_U_VAL 0x00000008 /* nPWE */
-#define CFG_GAFR2_L_VAL 0xA0000000 /* CS2, CS3 */
+#define CFG_GAFR2_L_VAL 0xA0000000 /* CS2, CS3 */
#define CFG_GAFR2_U_VAL 0x00000000
#define CFG_PSSR_VAL 0x00000020 /* Power manager sleep status */