da850/omap-l138: add support for direct NOR boot mode

[oweals/u-boot.git] / include / configs / xpedite537x.h

diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h
index e7de13a7ccb58ec9f545a9d965d37d0f0953e2fb..6a469bb6026c31bf0e698338a2504018052fd611 100644 (file)
--- a/include/configs/xpedite537x.h
+++ b/include/configs/xpedite537x.h
@@ -96,14 +96,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_BTB                     /* toggle branch predition */
 #define CONFIG_ENABLE_36BIT_PHYS       1
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR             0xef000000      /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR             0xef000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /*
  * Diagnostics
@@ -224,10 +218,9 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  */
 #define CONFIG_SYS_INIT_RAM_LOCK       1
 #define CONFIG_SYS_INIT_RAM_ADDR       0xe0000000
-#define CONFIG_SYS_INIT_RAM_END                0x00004000
+#define CONFIG_SYS_INIT_RAM_SIZE               0x00004000
 
-#define CONFIG_SYS_GBL_DATA_SIZE       128     /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN         (512 * 1024)    /* Reserve 512 KB for Mon */
@@ -253,7 +246,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  * Use the HUSH parser
  */
 #define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 
 /*
  * Pass open firmware flat tree
@@ -370,12 +362,21 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  */
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #define CONFIG_PHY_GIGE                1       /* Include GbE speed/duplex detection */
-#define CONFIG_NET_MULTI       1
 #define CONFIG_TSEC_TBI
 #define CONFIG_MII             1       /* MII PHY management */
 #define CONFIG_MII_DEFAULT_TSEC        1       /* Allow unregistered phys */
 #define CONFIG_ETHPRIME                "eTSEC2"
 
+/*
+ * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force
+ * 1000mbps SGMII link
+ */
+#define CONFIG_TSEC_TBICR_SETTINGS ( \
+               TBICR_PHY_RESET \
+               | TBICR_FULL_DUPLEX \
+               | TBICR_SPEED1_SET \
+               )
+
 #define CONFIG_TSEC1           1
 #define CONFIG_TSEC1_NAME      "eTSEC1"
 #define TSEC1_FLAGS            (TSEC_GIGABIT | TSEC_REDUCED)