#define CONFIG_SYS_NO_FLASH
-
/* Generic Interrupt Controller Definitions */
#define CONFIG_GICV2
#define GICD_BASE 0xF9010000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_SYS_MEMTEST_SCRATCH 0xfffc0000
-#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_SDRAM_SIZE
+#ifndef CONFIG_NR_DRAM_BANKS
+# define CONFIG_NR_DRAM_BANKS 2
+#endif
+#define CONFIG_SYS_MEMTEST_START 0
+#define CONFIG_SYS_MEMTEST_END 1000
/* Have release address at the end of 256MB for now */
#define CPU_RELEASE_ADDR 0xFFFFFF0
-/* Cache Definitions */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
-#define CONFIG_IDENT_STRING " Xilinx ZynqMP"
-
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
+#if !defined(CONFIG_IDENT_STRING)
+# define CONFIG_IDENT_STRING " Xilinx ZynqMP"
+#endif
-/* Flat Device Tree Definitions */
-#define CONFIG_OF_LIBFDT
+#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
/* Generic Timer Definitions - setup in EL3. Setup by ATF for other cases */
#if !defined(COUNTER_FREQUENCY)
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 0x2000000)
/* Serial setup */
-#if defined(CONFIG_ZYNQMP_DCC)
-# define CONFIG_ARM_DCC
-# define CONFIG_CPU_ARMV8
-#else
-# define CONFIG_ZYNQ_SERIAL
-#endif
+#define CONFIG_ARM_DCC
+#define CONFIG_CPU_ARMV8
+#define CONFIG_ZYNQ_SERIAL
#define CONFIG_CONS_INDEX 0
#define CONFIG_BAUDRATE 115200
/* Command line configuration */
#define CONFIG_CMD_ENV
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_EXT4
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_FS_GENERIC
#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#ifndef CONFIG_SPL_BUILD
+# define CONFIG_ISO_PARTITION
+#endif
#define CONFIG_MP
-#define CONFIG_CMD_MII
-
/* BOOTP options */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_MAY_FAIL
-#define CONFIG_BOOTP_SERVERIP
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_PXE
+#define CONFIG_BOOTP_SUBNETMASK
-/* SPI */
-#ifdef CONFIG_ZYNQ_SPI
-# define CONFIG_CMD_SF
-#endif
+/* Diff from config_distro_defaults.h */
+#define CONFIG_SUPPORT_RAW_INITRD
+#define CONFIG_ENV_VARS_UBOOT_CONFIG
+#define CONFIG_AUTO_COMPLETE
+
+/* PXE */
+#define CONFIG_CMD_PXE
+#define CONFIG_MENU
-#if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
+#if defined(CONFIG_ZYNQ_SDHCI)
# define CONFIG_MMC
# define CONFIG_GENERIC_MMC
+# define CONFIG_SUPPORT_EMMC_BOOT
# define CONFIG_SDHCI
-# define CONFIG_ZYNQ_SDHCI
-# define CONFIG_CMD_MMC
# ifndef CONFIG_ZYNQ_SDHCI_MAX_FREQ
# define CONFIG_ZYNQ_SDHCI_MAX_FREQ 200000000
# endif
#endif
-#if defined(CONFIG_ZYNQ_SDHCI)
+#if defined(CONFIG_ZYNQ_SDHCI) || defined(CONFIG_ZYNQMP_USB)
# define CONFIG_FAT_WRITE
-# define CONFIG_CMD_EXT4_WRITE
+#endif
+
+#ifdef CONFIG_NAND_ARASAN
+# define CONFIG_CMD_NAND_LOCK_UNLOCK
+# define CONFIG_SYS_MAX_NAND_DEVICE 1
+# define CONFIG_SYS_NAND_SELF_INIT
+# define CONFIG_SYS_NAND_ONFI_DETECTION
+# define CONFIG_MTD_DEVICE
#endif
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR 0x8000000
#if defined(CONFIG_ZYNQMP_USB)
-#define CONFIG_USB_XHCI_DWC3
-#define CONFIG_USB_XHCI
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
#define CONFIG_USB_XHCI_ZYNQMP
-#define CONFIG_USB_DWC3
-#define CONFIG_USB_DWC3_GADGET
-
-#define CONFIG_USB_GADGET
-#define CONFIG_USB_GADGET_DOWNLOAD
-#define CONFIG_USB_GADGET_DUALSPEED
-#define CONFIG_USB_GADGET_VBUS_DRAW 2
-#define CONFIG_USBDOWNLOAD_GADGET
#define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x1800000
#define DFU_DEFAULT_POLL_TIMEOUT 300
#define CONFIG_USB_FUNCTION_DFU
#define CONFIG_DFU_RAM
-#define CONFIG_G_DNL_VENDOR_NUM 0x03FD
-#define CONFIG_G_DNL_PRODUCT_NUM 0x0300
-#define CONFIG_G_DNL_MANUFACTURER "Xilinx"
#define CONFIG_USB_CABLE_CHECK
-#define CONFIG_CMD_DFU
#define CONFIG_CMD_THOR_DOWNLOAD
#define CONFIG_USB_FUNCTION_THOR
#define CONFIG_THOR_RESET_OFF
#define DFU_ALT_INFO_RAM \
"dfu_ram_info=" \
- "set dfu_alt_info " \
- "Image ram 0x200000 0x1800000\\\\;" \
- "system.dtb ram 0x7000000 0x40000\0" \
+ "setenv dfu_alt_info " \
+ "Image ram $kernel_addr $kernel_size\\\\;" \
+ "system.dtb ram $fdt_addr $fdt_size\0" \
"dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
"thor_ram=run dfu_ram_info && thordown 0 ram 0\0"
# define DFU_ALT_INFO
#endif
-/* Initial environment variables */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "kernel_addr=0x80000\0" \
- "fdt_addr=0x7000000\0" \
- "fdt_high=0x10000000\0" \
- "sdbootdev=0\0"\
- "sdboot=mmc dev $sdbootdev && mmcinfo && load mmc $sdbootdev:$partid $fdt_addr system.dtb && " \
- "load mmc $sdbootdev:$partid $kernel_addr Image && " \
- "booti $kernel_addr - $fdt_addr\0" \
- DFU_ALT_INFO
-
-#define CONFIG_BOOTARGS "setenv bootargs console=ttyPS0,${baudrate} " \
- "earlycon=cdns,mmio,0xff000000,${baudrate}n8"
-#define CONFIG_PREBOOT "run bootargs"
-#define CONFIG_BOOTCOMMAND "run $modeboot"
-#define CONFIG_BOOTDELAY 5
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_SYS_CBSIZE 2048
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
# define CONFIG_MII
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# define CONFIG_PHY_MARVELL
+# define CONFIG_PHY_NATSEMI
# define CONFIG_PHY_TI
+# define CONFIG_PHY_GIGE
+# define CONFIG_PHY_VITESSE
+# define CONFIG_PHY_REALTEK
+# define PHY_ANEG_TIMEOUT 20000
#endif
/* I2C */
#if defined(CONFIG_SYS_I2C_ZYNQ)
-# define CONFIG_CMD_I2C
# define CONFIG_SYS_I2C
# define CONFIG_SYS_I2C_ZYNQ_SPEED 100000
# define CONFIG_SYS_I2C_ZYNQ_SLAVE 0
# define CONFIG_SYS_EEPROM_SIZE (64 * 1024)
#endif
-#ifdef CONFIG_AHCI
+#ifdef CONFIG_SATA_CEVA
+#define CONFIG_AHCI
#define CONFIG_LIBATA
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
-#define CONFIG_CMD_SCSI
+#define CONFIG_SCSI
#endif
#define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024)
-#define CONFIG_CMD_BOOTI
#define CONFIG_CMD_UNZIP
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_CLOCKS
+#define ENV_MEM_LAYOUT_SETTINGS \
+ "fdt_high=10000000\0" \
+ "initrd_high=10000000\0" \
+ "fdt_addr_r=0x40000000\0" \
+ "pxefile_addr_r=0x10000000\0" \
+ "kernel_addr_r=0x18000000\0" \
+ "scriptaddr=0x02000000\0" \
+ "ramdisk_addr_r=0x02100000\0" \
+
+#if defined(CONFIG_ZYNQ_SDHCI)
+# define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0) func(MMC, mmc, 1)
+#else
+# define BOOT_TARGET_DEVICES_MMC(func)
+#endif
+
+#if defined(CONFIG_SATA_CEVA)
+# define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
+#else
+# define BOOT_TARGET_DEVICES_SCSI(func)
+#endif
+
+#if defined(CONFIG_ZYNQMP_USB)
+# define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0) func(USB, usb, 1)
+#else
+# define BOOT_TARGET_DEVICES_USB(func)
+#endif
+
+#define BOOT_TARGET_DEVICES(func) \
+ BOOT_TARGET_DEVICES_MMC(func) \
+ BOOT_TARGET_DEVICES_USB(func) \
+ BOOT_TARGET_DEVICES_SCSI(func) \
+ func(PXE, pxe, na) \
+ func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+/* Initial environment variables */
+#ifndef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ ENV_MEM_LAYOUT_SETTINGS \
+ BOOTENV \
+ DFU_ALT_INFO
+#endif
+
+#define CONFIG_SPL_TEXT_BASE 0xfffc0000
+#define CONFIG_SPL_STACK 0xfffffffc
+#define CONFIG_SPL_MAX_SIZE 0x20000
+
+/* Just random location in OCM */
+#define CONFIG_SPL_BSS_START_ADDR 0x1000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x2000000
+
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_RAM_DEVICE
+
+#define CONFIG_SPL_OS_BOOT
+/* u-boot is like dtb */
+#define CONFIG_SPL_FS_LOAD_ARGS_NAME "u-boot.bin"
+#define CONFIG_SYS_SPL_ARGS_ADDR 0x8000000
+
+/* ATF is my kernel image */
+#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "atf.ub"
+
+/* FIT load address for RAM boot */
+#define CONFIG_SPL_LOAD_FIT_ADDRESS 0x10000000
+
+/* MMC support */
+#ifdef CONFIG_ZYNQ_SDHCI
+# define CONFIG_SPL_MMC_SUPPORT
+# define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+# define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0 /* unused */
+# define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0 /* unused */
+# define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0 /* unused */
+# define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+#endif
+
#endif /* __XILINX_ZYNQMP_H */