/*
* KARO TX25 board - SoC Configuration
*/
-#define CONFIG_ARM926EJS /* arm926ejs CPU core */
#define CONFIG_MX25
-#define CONFIG_TX25
#define CONFIG_MX25_CLK32 32000 /* OSC32K frequency */
#define CONFIG_SYS_HZ 1000
/* NAND BOOT is the only boot method */
#define CONFIG_NAND_U_BOOT
+#ifndef MACH_TYPE_TX25
+#define MACH_TYPE_TX25 2177
+#endif
+
+#define CONFIG_MACH_TYPE MACH_TYPE_TX25
+
#ifdef CONFIG_NAND_SPL
/* Start copying real U-boot from the second page */
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x800
#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
/*
* Memory Info
/* 8MB DRAM test */
#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1+0x0800000)
-#define CONFIG_STACKSIZE (256 * 1024) /* regular stack */
/*
* Serial Info
*/
-#define CONFIG_MXC_UART 1
-#define CONFIG_SYS_MX25_UART1 1
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
#define CONFIG_BAUDRATE 115200 /* Default baud rate */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CONFIG_MXC_GPIO
/*
* Flash & Environment
*/
/* No NOR flash present */
-#define CONFIG_SYS_NO_FLASH 1
+#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET CONFIG_SYS_MONITOR_LEN
#define CONFIG_ENV_SIZE (128 * 1024) /* 128 kB NAND block size */
/* NAND */
#define CONFIG_NAND_MXC
-#define CONFIG_NAND_MXC_V1_1
#define CONFIG_MXC_NAND_REGS_BASE (0xBB000000)
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE (0xBB000000)
#define CONFIG_MXC_NAND_HWECC
#define CONFIG_SYS_NAND_LARGEPAGE
-#define CONFIG_SYS_64BIT_VSPRINTF
-
/* U-Boot general configuration */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_FEC_MXC_PHYADDR 0x1f
#define CONFIG_MII
#define CONFIG_CMD_NET
-#define CONFIG_NET_MULTI
-#define BOARD_LATE_INIT
+#define CONFIG_BOARD_LATE_INIT
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BOOTDELAY 5
#define CONFIG_LOADADDR 0x81000000 /* loadaddr env var */
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define xstr(s) str(s)
-#define str(s) #s
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
"addmisc=setenv bootargs ${bootargs}\0" \
"u-boot=tx25/u-boot.bin\0" \
- "kernel_addr_r=" xstr(CONFIG_LOADADDR) "\0" \
+ "kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
"hostname=tx25\0" \
"bootfile=tx25/uImage\0" \
"rootpath=/opt/eldk/arm\0" \