include/configs: remove CONFIG_SYS_CBSIZE when the default value is used

[oweals/u-boot.git] / include / configs / tao3530.h

diff --git a/include/configs/tao3530.h b/include/configs/tao3530.h
index 834fe174d64060e85d55a888a5445505d22f831b..b3a519b3416709bb040cbdc9eccfbefa293a7b4e 100644 (file)
--- a/include/configs/tao3530.h
+++ b/include/configs/tao3530.h
@@ -62,17 +62,13 @@
 #define CONFIG_ENV_OVERWRITE
 
 /* commands to include */
-#define CONFIG_CMD_MTDPARTS    /* Enable MTD parts commands */
 #define CONFIG_MTD_DEVICE      /* needed for mtdparts commands */
 #define MTDIDS_DEFAULT                 "nand0=nand"
 #define MTDPARTS_DEFAULT               "mtdparts=nand:512k(x-loader),"\
                                        "1920k(u-boot),128k(u-boot-env),"\
                                        "4m(kernel),-(fs)"
 
-#define CONFIG_CMD_NAND                /* NAND support                 */
-
 #define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_SYS_OMAP24_I2C_SPEED    100000
 #define CONFIG_SYS_OMAP24_I2C_SLAVE    1
 #define CONFIG_I2C_MULTI_BUS
@@ -152,7 +148,6 @@
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP            /* undef to save memory */
-#define CONFIG_SYS_CBSIZE              256     /* Console I/O Buffer Size */
 
 /* turn on command-line edit/hist/auto */
 #define CONFIG_CMDLINE_EDITING
@@ -203,7 +198,6 @@
 #define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_ONENAND_BASE                ONENAND_MAP
 
-#define CONFIG_ENV_IS_IN_NAND          1
 #define ONENAND_ENV_OFFSET             0x260000 /* environment starts here */
 #define SMNAND_ENV_OFFSET              0x260000 /* environment starts here */
 
@@ -218,8 +212,6 @@
                                         CONFIG_SYS_INIT_RAM_SIZE - \
                                         GENERATED_GBL_DATA_SIZE)
 
-#define CONFIG_OMAP3_SPI
-
 /*
  * USB
  *
@@ -228,11 +220,8 @@
  */
 
 /* USB EHCI */
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_OMAP
 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO       162
 
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
 #define CONFIG_USB_HOST_ETHER
 #define CONFIG_USB_ETHER_SMSC95XX
 
@@ -246,12 +235,9 @@
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME        "u-boot.img"
 
-#define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_NAND_BASE
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_ECC
-#define CONFIG_SPL_OMAP3_ID_NAND
-#define CONFIG_SPL_LDSCRIPT            "arch/arm/mach-omap2/u-boot-spl.lds"
 
 /* NAND boot config */
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE