Merge branch 'sandbox' of git://git.denx.de/u-boot-x86

[oweals/u-boot.git] / include / configs / socfpga_common.h

diff --git a/include/configs/socfpga_common.h b/include/configs/socfpga_common.h
index e1aae4934d2cd72fea3b524a7d7b28475afdbfa5..c4ac94d0eb302ec6c64193fc99f109f069b00de8 100644 (file)
--- a/include/configs/socfpga_common.h
+++ b/include/configs/socfpga_common.h
@@ -11,7 +11,6 @@
 /* Virtual target or real hardware */
 #undef CONFIG_SOCFPGA_VIRTUAL_TARGET
 
-#define CONFIG_ARMV7
 #define CONFIG_SYS_THUMB_BUILD
 
 #define CONFIG_SOCFPGA
@@ -78,6 +77,25 @@
 #define CONFIG_SYS_L2_PL310
 #define CONFIG_SYS_PL310_BASE          SOCFPGA_MPUL2_ADDRESS
 
+/*
+ * EPCS/EPCQx1 Serial Flash Controller
+ */
+#ifdef CONFIG_ALTERA_SPI
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED                30000000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_BAR
+/*
+ * The base address is configurable in QSys, each board must specify the
+ * base address based on it's particular FPGA configuration. Please note
+ * that the address here is incremented by  0x400  from the Base address
+ * selected in QSys, since the SPI registers are at offset +0x400.
+ * #define CONFIG_SYS_SPI_BASE         0xff240400
+ */
+#endif
+
 /*
  * Ethernet on SoC (EMAC)
  */
@@ -141,6 +159,33 @@
 #define CONFIG_SYS_MMC_MAX_BLK_COUNT   256     /* FIXME -- SPL only? */
 #endif
 
+ /*
+ * I2C support
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_DW
+#define CONFIG_SYS_I2C_BUS_MAX         4
+#define CONFIG_SYS_I2C_BASE            SOCFPGA_I2C0_ADDRESS
+#define CONFIG_SYS_I2C_BASE1           SOCFPGA_I2C1_ADDRESS
+#define CONFIG_SYS_I2C_BASE2           SOCFPGA_I2C2_ADDRESS
+#define CONFIG_SYS_I2C_BASE3           SOCFPGA_I2C3_ADDRESS
+/* Using standard mode which the speed up to 100Kb/s */
+#define CONFIG_SYS_I2C_SPEED           100000
+#define CONFIG_SYS_I2C_SPEED1          100000
+#define CONFIG_SYS_I2C_SPEED2          100000
+#define CONFIG_SYS_I2C_SPEED3          100000
+/* Address of device when used as slave */
+#define CONFIG_SYS_I2C_SLAVE           0x02
+#define CONFIG_SYS_I2C_SLAVE1          0x02
+#define CONFIG_SYS_I2C_SLAVE2          0x02
+#define CONFIG_SYS_I2C_SLAVE3          0x02
+#ifndef __ASSEMBLY__
+/* Clock supplied to I2C controller in unit of MHz */
+unsigned int cm_get_l4_sp_clk_hz(void);
+#define IC_CLK                         (cm_get_l4_sp_clk_hz() / 1000000)
+#endif
+#define CONFIG_CMD_I2C
+
 /*
  * Serial Driver
  */