* High Level Configuration Options
* (easy to change)
*/
-#define CONFIG_ARM920T 1 /* This is an ARM920T Core */
-#define CONFIG_S3C24X0 1 /* in a SAMSUNG S3C24x0-type SoC */
-#define CONFIG_S3C2410 1 /* specifically a SAMSUNG S3C2410 SoC */
-#define CONFIG_SMDK2410 1 /* on a SAMSUNG SMDK2410 Board */
+#define CONFIG_ARM920T /* This is an ARM920T Core */
+#define CONFIG_S3C24X0 /* in a SAMSUNG S3C24x0-type SoC */
+#define CONFIG_S3C2410 /* specifically a SAMSUNG S3C2410 SoC */
+#define CONFIG_SMDK2410 /* on a SAMSUNG SMDK2410 Board */
-/* input clock of PLL */
-#define CONFIG_SYS_CLK_FREQ 12000000/* the SMDK2410 has 12MHz input clock */
+#define CONFIG_SYS_TEXT_BASE 0x0
+#define CONFIG_SYS_ARM_CACHE_WRITETHROUGH
-#define USE_920T_MMU 1
-#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
+/* input clock of PLL (the SMDK2410 has 12MHz input clock) */
+#define CONFIG_SYS_CLK_FREQ 12000000
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
/*
* Hardware drivers
*/
-#define CONFIG_NET_MULTI
#define CONFIG_CS8900 /* we have a CS8900 on-board */
#define CONFIG_CS8900_BASE 0x19000300
#define CONFIG_CS8900_BUS16 /* the Linux driver does accesses as shorts */
* select serial console configuration
*/
#define CONFIG_S3C24X0_SERIAL
-#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on SMDK2410 */
+#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on SMDK2410 */
+
+/************************************************************
+ * USB support (currently only works with D-cache off)
+ ************************************************************/
+#define CONFIG_USB_OHCI
+#define CONFIG_USB_OHCI_S3C24XX
+#define CONFIG_USB_KEYBOARD
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
/************************************************************
* RTC
************************************************************/
-#define CONFIG_RTC_S3C24X0 1
+#define CONFIG_RTC_S3C24X0
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
-
/*
* BOOTP options
*/
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
+#define CONFIG_CMD_BSP
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ELF
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_USB
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_CMDLINE_EDITING
-#define CONFIG_BOOTDELAY 3
-/*#define CONFIG_BOOTARGS "root=ramfs devfs=mount console=ttySA0,9600" */
-/*#define CONFIG_ETHADDR 08:00:3e:26:0a:5b */
-#define CONFIG_NETMASK 255.255.255.0
+/* autoboot */
+#define CONFIG_BOOTDELAY 5
+#define CONFIG_BOOT_RETRY_TIME -1
+#define CONFIG_RESET_TO_RETRY
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_IPADDR 10.0.0.110
#define CONFIG_SERVERIP 10.0.0.1
-/*#define CONFIG_BOOTFILE "elinos-lart" */
-/*#define CONFIG_BOOTCOMMAND "tftp; bootm" */
#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
/* what's this ? it's not used anywhere */
-#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "SMDK2410 # " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "SMDK2410 # "
+#define CONFIG_SYS_CBSIZE 256
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_MEMTEST_START 0x30000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x33F00000 /* 63 MB in DRAM */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
-#define CONFIG_SYS_LOAD_ADDR 0x33000000 /* default load address */
+#define CONFIG_SYS_MEMTEST_START 0x30000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x33F00000 /* 63 MB in DRAM */
-#define CONFIG_SYS_HZ 1000
+#define CONFIG_SYS_LOAD_ADDR 0x30800000
-/* valid baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_HZ 1000
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
-#endif
+/* support additional compression methods */
+#define CONFIG_BZIP2
+#define CONFIG_LZO
+#define CONFIG_LZMA
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
+#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define PHYS_SDRAM_1 0x30000000 /* SDRAM Bank #1 */
#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
-#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #0 */
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CONFIG_AMD_LV400 1 /* uncomment this if you have a LV400 flash */
-#if 0
-#define CONFIG_AMD_LV800 1 /* uncomment this if you have a LV800 flash */
-#endif
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_LEGACY
+#define CONFIG_SYS_FLASH_LEGACY_512Kx16
+#define CONFIG_FLASH_SHOW_PROGRESS 45
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#ifdef CONFIG_AMD_LV800
-#define PHYS_FLASH_SIZE 0x00100000 /* 1MB */
-#define CONFIG_SYS_MAX_FLASH_SECT (19) /* max number of sectors on one chip */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x0F0000) /* addr of environment */
-#endif
-#ifdef CONFIG_AMD_LV400
-#define PHYS_FLASH_SIZE 0x00080000 /* 512KB */
-#define CONFIG_SYS_MAX_FLASH_SECT (11) /* max number of sectors on one chip */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x070000) /* addr of environment */
-#endif
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+#define CONFIG_SYS_MAX_FLASH_SECT (19)
+
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x070000)
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SIZE 0x10000
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (5*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (5*CONFIG_SYS_HZ) /* Timeout for Flash Write */
+/*
+ * Size of malloc() pool
+ * BZIP2 / LZO / LZMA need a lot of RAM
+ */
+#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
+#define CONFIG_SYS_MONITOR_LEN (448 * 1024)
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_S3C2410
+#define CONFIG_SYS_S3C2410_NAND_HWECC
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x4E000000
+#endif
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_YAFFS2
+#define CONFIG_RBTREE
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \
GENERATED_GBL_DATA_SIZE)
+#define CONFIG_BOARD_EARLY_INIT_F
-#endif /* __CONFIG_H */
+#endif /* __CONFIG_H */