#define CONFIG_SCB9328 1 /* on a scb9328tronix board */
#undef CONFIG_USE_IRQ /* don't need use IRQ/FIQ */
+#define CONFIG_IMX_SERIAL
#define CONFIG_IMX_SERIAL1
/*
* Select serial console configuration
/*
- * Definition of u-boot build in commands. Check out CONFIG_CMD_DFL if
- * neccessary in include/cmd_confdefs.h file. (Un)comment for getting
- * functionality or size of u-boot code.
+ * BOOTP options
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- & ~CFG_CMD_LOADS \
- & ~CFG_CMD_CONSOLE \
- & ~CFG_CMD_AUTOSCRIPT \
- | CFG_CMD_NET \
- | CFG_CMD_PING \
- | CFG_CMD_DHCP \
- )
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_CONSOLE
+#undef CONFIG_CMD_AUTOSCRIPT
-#include <cmd_confdefs.h>
/*
* Boot options. Setting delay to -1 stops autostart count down.
/*
* General options for u-boot. Modify to save memory foot print
*/
-#define CFG_LONGHELP /* undef saves memory */
-#define CFG_PROMPT "scb9328> " /* prompt string */
-#define CFG_CBSIZE 256 /* console I/O buffer */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer size */
-#define CFG_MAXARGS 16 /* max command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* boot args buf size */
+#define CONFIG_SYS_LONGHELP /* undef saves memory */
+#define CONFIG_SYS_PROMPT "scb9328> " /* prompt string */
+#define CONFIG_SYS_CBSIZE 256 /* console I/O buffer */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* print buffer size */
+#define CONFIG_SYS_MAXARGS 16 /* max command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* boot args buf size */
-#define CFG_MEMTEST_START 0x08100000 /* memtest test area */
-#define CFG_MEMTEST_END 0x08F00000
+#define CONFIG_SYS_MEMTEST_START 0x08100000 /* memtest test area */
+#define CONFIG_SYS_MEMTEST_END 0x08F00000
-#undef CFG_CLKS_IN_HZ /* use HZ for freq. display */
+#define CONFIG_SYS_HZ 3686400 /* incrementer freq: 3.6864 MHz */
+#define CONFIG_SYS_CPUSPEED 0x141 /* core clock - register value */
-#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
-#define CFG_CPUSPEED 0x141 /* core clock - register value */
-
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_BAUDRATE 115200
/*
* Definitions related to passing arguments to kernel.
/*
* Malloc pool need to host env + 128 Kb reserve for other allocations.
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + (128<<10) )
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128<<10) )
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CONFIG_STACKSIZE (120<<10) /* stack size */
/* 32MB */
#ifdef SCB9328_FLASH_32M
-#define CFG_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
-#define CFG_MAX_FLASH_SECT 256 /* number of sector in FLASH bank */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* number of sector in FLASH bank */
#define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */
#define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */
#define SCB9328_FLASH_BANK_SIZE 0x02000000 /* size of one flash bank */
#else
/* 16MB */
-#define CFG_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
-#define CFG_MAX_FLASH_SECT 128 /* number of sector in FLASH bank */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* number of sector in FLASH bank */
#define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */
#define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */
#define SCB9328_FLASH_BANK_SIZE 0x01000000 /* size of one flash bank */
is not so clear to me. In other words we can provide more informations
to user, but this expects more complex flash handling we do not provide
now.*/
-#undef CFG_FLASH_CFI
+#undef CONFIG_SYS_FLASH_CFI
-#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* timeout for Erase operation */
-#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* timeout for Write operation */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* timeout for Erase operation */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* timeout for Write operation */
-#define CFG_FLASH_BASE SCB9328_FLASH_BASE
+#define CONFIG_SYS_FLASH_BASE SCB9328_FLASH_BASE
/*
* This is setting for JFFS2 support in u-boot.
* Right now there is no gain for user, but later on booting kernel might be
* possible. Consider using XIP kernel running from flash to save RAM
* footprint.
- * NOTE: Enable CFG_CMD_JFFS2 for JFFS2 support.
+ * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
*/
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_FIRST_SECTOR 5
-#define CFG_JFFS2_NUM_BANKS 1
+#define CONFIG_SYS_JFFS2_FIRST_BANK 0
+#define CONFIG_SYS_JFFS2_FIRST_SECTOR 5
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
/*
* Environment setup. Definitions of monitor location and size with
/* Setup for PA23 which is Reset Default PA23 but has to become
CS5 */
-#define CFG_GPR_A_VAL 0x00800000
-#define CFG_GIUS_A_VAL 0x0043fffe
+#define CONFIG_SYS_GPR_A_VAL 0x00800000
+#define CONFIG_SYS_GIUS_A_VAL 0x0043fffe
-#define CFG_MONITOR_BASE 0x10000000
-#define CFG_MONITOR_LEN 0x20000 /* 128b ( 1 flash sector ) */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR 0x10020000 /* absolute address for now */
-#define CFG_ENV_SIZE 0x20000
+#define CONFIG_SYS_MONITOR_BASE 0x10000000
+#define CONFIG_SYS_MONITOR_LEN 0x20000 /* 128b ( 1 flash sector ) */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR 0x10020000 /* absolute address for now */
+#define CONFIG_ENV_SIZE 0x20000
#define CONFIG_ENV_OVERWRITE 1 /* env is not writable now */
* | OEA | OEN | WEA | WEN | CSA |EBC| DSZ | 0|SP|0|WP| 0 0|PA|CSEN|
*/
-#define CFG_CS0U_VAL 0x000F2000
-#define CFG_CS0L_VAL 0x11110d01
-#define CFG_CS1U_VAL 0x000F0a00
-#define CFG_CS1L_VAL 0x11110601
-#define CFG_CS2U_VAL 0x0
-#define CFG_CS2L_VAL 0x0
+#define CONFIG_SYS_CS0U_VAL 0x000F2000
+#define CONFIG_SYS_CS0L_VAL 0x11110d01
+#define CONFIG_SYS_CS1U_VAL 0x000F0a00
+#define CONFIG_SYS_CS1L_VAL 0x11110601
+#define CONFIG_SYS_CS2U_VAL 0x0
+#define CONFIG_SYS_CS2L_VAL 0x0
-#define CFG_CS3U_VAL 0x000FFFFF
-#define CFG_CS3L_VAL 0x00000303
+#define CONFIG_SYS_CS3U_VAL 0x000FFFFF
+#define CONFIG_SYS_CS3L_VAL 0x00000303
-#define CFG_CS4U_VAL 0x000F0a00
-#define CFG_CS4L_VAL 0x11110301
+#define CONFIG_SYS_CS4U_VAL 0x000F0a00
+#define CONFIG_SYS_CS4L_VAL 0x11110301
/* CNC == 3 too long
- #define CFG_CS5U_VAL 0x0000C210 */
+ #define CONFIG_SYS_CS5U_VAL 0x0000C210 */
-/* #define CFG_CS5U_VAL 0x00008400
+/* #define CONFIG_SYS_CS5U_VAL 0x00008400
mal laenger mahcen, ob der bei 150MHz laenger haelt dann und
kaum langsamer ist */
-/* #define CFG_CS5U_VAL 0x00009400
- #define CFG_CS5L_VAL 0x11010D03 */
+/* #define CONFIG_SYS_CS5U_VAL 0x00009400
+ #define CONFIG_SYS_CS5L_VAL 0x11010D03 */
-#define CFG_CS5U_VAL 0x00008400
-#define CFG_CS5L_VAL 0x00000D03
+#define CONFIG_SYS_CS5U_VAL 0x00008400
+#define CONFIG_SYS_CS5L_VAL 0x00000D03
-#define CONFIG_DRIVER_DM9000 1
#define CONFIG_DRIVER_DM9000 1
#define CONFIG_DM9000_BASE 0x16000000
#define DM9000_IO CONFIG_DM9000_BASE
#define DM9000_DATA (CONFIG_DM9000_BASE+4)
-/* #define CONFIG_DM9000_USE_8BIT */
-#define CONFIG_DM9000_USE_16BIT
-/* #define CONFIG_DM9000_USE_32BIT */
/* f_{dpll}=2*f{ref}*(MFI+MFN/(MFD+1))/(PD+1)
f_ref=16,777MHz
#define CPU200
#ifdef CPU200
-#define CFG_MPCTL0_VAL 0x00321431
+#define CONFIG_SYS_MPCTL0_VAL 0x00321431
#else
-#define CFG_MPCTL0_VAL 0x040e200e
+#define CONFIG_SYS_MPCTL0_VAL 0x040e200e
#endif
/* #define BUS64 */
#define BUS72
#ifdef BUS72
-#define CFG_SPCTL0_VAL 0x04002400
+#define CONFIG_SYS_SPCTL0_VAL 0x04002400
#endif
#ifdef BUS96
-#define CFG_SPCTL0_VAL 0x04001800
+#define CONFIG_SYS_SPCTL0_VAL 0x04001800
#endif
#ifdef BUS64
-#define CFG_SPCTL0_VAL 0x08001800
+#define CONFIG_SYS_SPCTL0_VAL 0x08001800
#endif
/* Das ist der BCLK Divider, der aus der System PLL
Bit 21: MPLL Restart */
#ifdef BUS64
-#define CFG_CSCR_VAL 0x2f030003
+#define CONFIG_SYS_CSCR_VAL 0x2f030003
#endif
#ifdef BUS72
-#define CFG_CSCR_VAL 0x2f030403
+#define CONFIG_SYS_CSCR_VAL 0x2f030403
#endif
/*
* one may expect. For instance loadb command do not cares :-)
* So advice is - do not relay on this...
*/
-#define CFG_LOAD_ADDR 0x08400000
+#define CONFIG_SYS_LOAD_ADDR 0x08400000
#define MHZ16QUARZINUSE
#define CONFIG_SYS_CLK_FREQ 16780000
/* FMCR Bit 0 becomes 0 to make CS3 CS3 :P */
-#define CFG_FMCR_VAL 0x00000001
+#define CONFIG_SYS_FMCR_VAL 0x00000001
/* Bit[0:3] contain PERCLK1DIV for UART 1
0x000b00b ->b<- -> 192MHz/12=16MHz
0x000b00b ->3<- -> 64MHz/4=16MHz */
#ifdef BUS96
-#define CFG_PCDR_VAL 0x000b00b5
+#define CONFIG_SYS_PCDR_VAL 0x000b00b5
#endif
#ifdef BUS64
-#define CFG_PCDR_VAL 0x000b00b3
+#define CONFIG_SYS_PCDR_VAL 0x000b00b3
#endif
#ifdef BUS72
-#define CFG_PCDR_VAL 0x000b00b8
+#define CONFIG_SYS_PCDR_VAL 0x000b00b8
#endif
#endif /* __CONFIG_H */