Merging Stelian Pop AT91 patches

[oweals/u-boot.git] / include / configs / sc520_spunk.h

diff --git a/include/configs/sc520_spunk.h b/include/configs/sc520_spunk.h
index 9d26beb21df28e7cc3c201640a8bd151697464cc..051b2e0f583e785c3726e7976d2319999072180a 100644 (file)
--- a/include/configs/sc520_spunk.h
+++ b/include/configs/sc520_spunk.h
@@ -64,16 +64,38 @@
 
 #define CONFIG_BAUDRATE                9600
 
-#define CONFIG_COMMANDS         (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_JFFS2 | CFG_CMD_IDE | CFG_CMD_NET | CFG_CMD_PCMCIA | CFG_CMD_EEPROM)
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
 
-#define CONFIG_BOOTDELAY       15
-#define CONFIG_BOOTARGS        "root=/dev/mtdblock1 console=ttyS0,9600 mtdparts=phys:7936k(root),256k(uboot) "
-#define CONFIG_BOOTCOMMAND     "setenv bootargs root=/dev/nfs ip=autoconf console=ttyS0,9600 mtdparts=phys:7808k(root),128k(env),256k(uboot); bootp; bootm"
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCMCIA
+#define CONFIG_CMD_EEPROM
+
+
+#define CONFIG_BOOTDELAY       15
+#define CONFIG_BOOTARGS                "root=/dev/mtdblock1 console=ttyS0,9600 " \
+                                       "mtdparts=phys:7936k(root),256k(uboot) "
+#define CONFIG_BOOTCOMMAND     "setenv bootargs root=/dev/nfs ip=autoconf " \
+                                       "console=ttyS0,9600 " \
+                                       "mtdparts=phys:7808k(root),128k(env),256k(uboot);" \
+                                       "bootp;bootm"
+
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   115200          /* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2               /* which serial port to use */
 #endif
@@ -147,8 +169,23 @@
 
 #endif
 
-#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS     1           /*  */
+/*
+ * JFFS2 partitions
+ *
+ */
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV               "nor0"
+#define CONFIG_JFFS2_PART_SIZE         0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET       0x00000000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT         "nor0=sc520_spunk-0"
+#define MTDPARTS_DEFAULT       "mtdparts=sc520_spunk-0:-(jffs2)"
+*/
 
 /*-----------------------------------------------------------------------
  * Device drivers
@@ -169,7 +206,7 @@
 #define CFG_ATA_REG_OFFSET     0       /* reg offset */
 #define CFG_ATA_ALT_OFFSET     0x200   /* alternate register offset */
 
-#define CFG_FISRT_PCMCIA_BUS    1
+#define CFG_FIRST_PCMCIA_BUS    1
 
 #undef CONFIG_IDE_LED                  /* no led for ide supported     */
 #undef  CONFIG_IDE_RESET               /* reset for ide unsupported... */