#ifndef __CONFIG_H
#define __CONFIG_H
+#define GRUSS_TESTING
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_X86 1 /* This is a X86 CPU */
+#define CONFIG_SC520 1 /* Include support for AMD SC520 */
+#define CONFIG_ALI152X 1 /* Include support for Ali 152x SIO */
-#define CFG_SDRAM_PRECHARGE_DELAY 6 /* 6T */
-#define CFG_SDRAM_REFRESH_RATE 78 /* 7.8uS (choices are 7.8, 15.6, 31.2 or 62.5uS) */
-#define CFG_SDRAM_RAS_CAS_DELAY 3 /* 3T */
+#define CONFIG_SYS_SDRAM_PRECHARGE_DELAY 6 /* 6T */
+#define CONFIG_SYS_SDRAM_REFRESH_RATE 78 /* 7.8uS (choices are 7.8, 15.6, 31.2 or 62.5uS) */
+#define CONFIG_SYS_SDRAM_RAS_CAS_DELAY 3 /* 3T */
/* define at most one of these */
-#undef CFG_SDRAM_CAS_LATENCY_2T
-#define CFG_SDRAM_CAS_LATENCY_3T
-
-#define CFG_SC520_HIGH_SPEED 0 /* 100 or 133MHz */
-#define CFG_RESET_GENERIC 1 /* use tripple-fault to reset cpu */
-#undef CFG_RESET_SC520 /* use SC520 MMCR's to reset cpu */
-#undef CFG_TIMER_SC520 /* use SC520 swtimers */
-#define CFG_TIMER_GENERIC 1 /* use the i8254 PIT timers */
-#undef CFG_TIMER_TSC /* use the Pentium TSC timers */
-#define CFG_USE_SIO_UART 0 /* prefer the uarts on the SIO to those
+#undef CONFIG_SYS_SDRAM_CAS_LATENCY_2T
+#define CONFIG_SYS_SDRAM_CAS_LATENCY_3T
+
+#define CONFIG_SYS_SC520_HIGH_SPEED 0 /* 100 or 133MHz */
+#undef CONFIG_SYS_RESET_SC520 /* use SC520 MMCR's to reset cpu */
+#undef CONFIG_SYS_TIMER_SC520 /* use SC520 swtimers */
+#define CONFIG_SYS_TIMER_GENERIC 1 /* use the i8254 PIT timers */
+#undef CONFIG_SYS_TIMER_TSC /* use the Pentium TSC timers */
+#define CONFIG_SYS_USE_SIO_UART 0 /* prefer the uarts on the SIO to those
* in the SC520 on the CDP */
-#define CFG_STACK_SIZE 0x8000 /* Size of bootloader stack */
+#define CONFIG_SYS_STACK_SIZE 0x8000 /* Size of bootloader stack */
#define CONFIG_SHOW_BOOT_PROGRESS 1
#define CONFIG_LAST_STAGE_INIT 1
/*
* Size of malloc() pool
*/
-#define CONFIG_MALLOC_SIZE (CFG_ENV_SIZE + 128*1024)
+#define CONFIG_MALLOC_SIZE (CONFIG_ENV_SIZE + 128*1024)
+#define CONFIG_BAUDRATE 9600
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CFG_ENV_IS_NOWHERE 1
-#undef CFG_ENV_IS_IN_FLASH
-#undef CFG_ENV_IS_IN_NVRAM
-#undef CFG_ENV_IS_INEEPROM
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_JFFS2 | CFG_CMD_IDE | CFG_CMD_NET)
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_CMD_PCI
+#ifndef GRUSS_TESTING
+#define CONFIG_CMD_SATA
+#else
+#undef CONFIG_CMD_SATA
+#endif
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_EEPROM
#define CONFIG_BOOTDELAY 15
-#define CONFIG_BOOTARGS "root=/dev/mtdblock0 console=ttyS0,9600"
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 console=ttyS0,9600"
/* #define CONFIG_BOOTCOMMAND "bootm 38000000" */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* */
-
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "boot > " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "boot > " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x01000000 /* 1 ... 16 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 1 ... 16 MB in DRAM */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
-#define CFG_LOAD_ADDR 0x38000000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1024 /* incrementer freq: 1kHz */
+#define CONFIG_SYS_HZ 1024 /* incrementer freq: 1kHz */
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 4 /* we have 4 banks of DRAM */
-
-#define PHYS_FLASH_1 0x38000000 /* Flash Bank #1 */
-#define PHYS_FLASH_SIZE 0x00800000 /* 8 MB */
-
-#define CFG_FLASH_BASE PHYS_FLASH_1
-
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (2*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x7a0000) /* Addr of Environment Sector */
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#define CONFIG_SPI_EEPROM /* Support for SPI EEPROMs (AT25128) */
+#define CONFIG_MW_EEPROM /* Support for MicroWire EEPROMs (AT93LC46) */
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Environment in EEPROM */
+#define CONFIG_ENV_IS_IN_EEPROM 1
+#define CONFIG_SPI
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment EEPROM 16k is SPI is used or 128 bytes if MW is used*/
+#define CONFIG_ENV_OFFSET 0
+#define CONFIG_SC520_CDP_USE_SPI /* Store configuration in the SPI part */
+#undef CONFIG_SC520_CDP_USE_MW /* Store configuration in the MicroWire part */
+#define CONFIG_SPI_X 1
+
+/*
+ * JFFS2 partitions
+ */
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=SC520CDP Flash Bank #0"
+#define MTDPARTS_DEFAULT "mtdparts=SC520CDP Flash Bank #0:-(jffs2)"
+*/
/*-----------------------------------------------------------------------
* Device drivers
#define CONFIG_PCNET_79C973
#define CONFIG_PCNET_79C975
#define PCNET_HAS_PROM 1
-/************************************************************
- * IDE/ATA stuff
- ************************************************************/
-#define CFG_IDE_MAXBUS 2 /* max. 2 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-
-#define CFG_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
-#define CFG_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
-#define CFG_ATA_DATA_OFFSET 0 /* data reg offset */
-#define CFG_ATA_REG_OFFSET 0 /* reg offset */
-#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */
-
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* reset for ide unsupported... */
-#undef CONFIG_IDE_RESET_ROUTINE /* no special reset function */
/************************************************************
- * ATAPI support (experimental)
- ************************************************************/
-#define CONFIG_ATAPI /* enable ATAPI Support */
+*SATA/Native Stuff
+************************************************************/
+#ifndef GRUSS_TESTING
+#define CONFIG_SYS_SATA_MAXBUS 2 /*Max Sata buses supported */
+#define CONFIG_SYS_SATA_DEVS_PER_BUS 2 /*Max no. of devices per bus/port */
+#define CONFIG_SYS_SATA_MAX_DEVICE (CONFIG_SYS_SATA_MAXBUS* CONFIG_SYS_SATA_DEVS_PER_BUS)
+#define CONFIG_ATA_PIIX 1 /*Supports ata_piix driver */
+#else
+#undef CONFIG_SYS_SATA_MAXBUS
+#undef CONFIG_SYS_SATA_DEVS_PER_BUS
+#undef CONFIG_SYS_SATA_MAX_DEVICE
+#undef CONFIG_ATA_PIIX
+#endif
+
/************************************************************
* DISK Partition support
#define CONFIG_ISO_PARTITION /* Experimental */
/************************************************************
- * Keyboard support
- ************************************************************/
-#define CONFIG_ISA_KEYBOARD
-
-#if 0
-/************************************************************
- * Video support
+ * Video/Keyboard support
************************************************************/
-#define CONFIG_VIDEO /*To enable video controller support */
-#define CONFIG_VIDEO_CT69000
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VIDEO_ONBOARD /* Video controller is on-board */
+#ifndef GRUSS_TESTING
+#define CONFIG_VIDEO /* To enable video controller support */
+#else
+#undef CONFIG_VIDEO
#endif
+#define CONFIG_I8042_KBD
+#define CONFIG_SYS_ISA_IO 0
/************************************************************
* RTC
/*
* PCI stuff
*/
+#ifndef GRUSS_TESTING
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_SYS_FIRST_PCI_IRQ 10
+#define CONFIG_SYS_SECOND_PCI_IRQ 9
+#define CONFIG_SYS_THIRD_PCI_IRQ 11
+#define CONFIG_SYS_FORTH_PCI_IRQ 15
+#else
+#undef CONFIG_PCI
+#undef CONFIG_PCI_PNP
+#undef CONFIG_PCI_SCAN_SHOW
+#endif
+
+
#endif /* __CONFIG_H */
projects / oweals / u-boot.git / blobdiff