* 0xFFE00000 .... 0xFFFFFFFF -> BOOT-ROM (2 MiB)
*/
-#define CONFIG_SOLIDCARD3 1
+#define CONFIG_SC3 1
#define CONFIG_4xx 1
#define CONFIG_405GP 1
* Define IDE_USES_ISA_EMULATION for slower IDE access in the ISA-IO address range
* If undefined, IDE access uses a seperat emulation with higher access speed.
* Consider to inform your Linux IDE driver about the different addresses!
- * IDE_USES_ISA_EMULATION is only used if your CONFIG_COMMANDS macro includes
- * the CFG_CMD_IDE macro!
+ * IDE_USES_ISA_EMULATION is only used if you define CONFIG_CMD_IDE!
*/
#define IDE_USES_ISA_EMULATION
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
+ "addcons=setenv bootargs ${bootargs} " \
+ "console=ttyS0,${baudrate}\0" \
+ "flash_nfs=run nfsargs addip addcons;" \
"bootm ${kernel_addr}\0" \
- "flash_nand=nand_args addip addcon;bootm ${kernel_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
+ "flash_nand=run nand_args addip addcons;bootm ${kernel_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;" \
+ "bootm\0" \
"rootpath=/opt/eldk/ppc_4xx\0" \
"bootfile=/tftpboot/sc3/uImage\0" \
"u-boot=/tftpboot/sc3/u-boot.bin\0" \
#if 1 /* feel free to disable for development */
#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */
-#define CONFIG_AUTOBOOT_PROMPT "\nSC3 - booting... stop with S\n"
-#define CONFIG_AUTOBOOT_DELAY_STR "S" /* 1st "password" */
+#define CONFIG_AUTOBOOT_PROMPT "\nSC3 - booting... stop with ENTER\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "\r" /* 1st "password" */
+#define CONFIG_AUTOBOOT_DELAY_STR2 "\n" /* 1st "password" */
#endif
/*
#define CONFIG_MII 1 /* add 405GP MII PHY management */
#define CONFIG_PHY_ADDR 1 /* the connected Phy defaults to address 1 */
-#define CONFIG_COMMANDS \
- (CONFIG_CMD_DFL | \
- CFG_CMD_AUTOSCRIPT | \
- CFG_CMD_PCI | \
- CFG_CMD_IRQ | \
- CFG_CMD_NET | \
- CFG_CMD_MII | \
- CFG_CMD_PING | \
- CFG_CMD_NAND | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_I2C | \
- CFG_CMD_IDE | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_CACHE | \
- CFG_CMD_ELF )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_ELF
+
#undef CONFIG_WATCHDOG /* watchdog disabled */
* External peripheral base address
*-----------------------------------------------------------------------
*/
-#if !(CONFIG_COMMANDS & CFG_CMD_IDE)
+#if !defined(CONFIG_CMD_IDE)
#undef CONFIG_IDE_LED /* no led for ide supported */
#undef CONFIG_IDE_RESET /* no reset for ide supported */
* IDE/ATA stuff
*-----------------------------------------------------------------------
*/
-#else /* !(CONFIG_COMMANDS & CFG_CMD_IDE) */
+#else
#define CONFIG_START_IDE 1 /* check, if use IDE */
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#endif /* IDE_USES_ISA_EMULATION */
-#endif /* !(CONFIG_COMMANDS & CFG_CMD_IDE) */
+#endif
/*
#define CFG_KEY_REG_BASE_ADDR 0xF0100000
#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-/* No command line, one static partition Partition 3 contains jffs2 rootfs */
+/* No command line, one static partition */
#undef CONFIG_JFFS2_CMDLINE
#define CONFIG_JFFS2_DEV "nand0"
-#define CONFIG_JFFS2_PART_SIZE 0x00400000
-#define CONFIG_JFFS2_PART_OFFSET 0x00c00000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- *
- * CFG_DCACHE_SIZE -> size of data cache:
- * - 405GP 8k
- * - 405GPr 16k
- * How to handle the difference in chache size?
- * CFG_CACHELINE_SIZE -> size of one cache line: 32 bytes
- * (used in cpu/ppc4xx/start.S)
-*/
-#define CFG_DCACHE_SIZE 16384
-
-#define CFG_CACHELINE_SIZE 32
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
- #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_JFFS2_PART_SIZE 0x01000000
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/*
* Init Memory Controller:
projects / oweals / u-boot.git / blobdiff