+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* WindRiver SBC8349 U-Boot configuration file.
* Copyright (c) 2006, 2007 Wind River Systems, Inc.
*
* Paul Gortmaker <paul.gortmaker@windriver.com>
* Based on the MPC8349EMDS config.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 Family */
-#define CONFIG_MPC834x 1 /* MPC834x family */
-#define CONFIG_MPC8349 1 /* MPC8349 specific */
-#define CONFIG_SBC8349 1 /* WRS SBC8349 board specific */
-
-#define CONFIG_SYS_TEXT_BASE 0xFF800000
/* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
-/*
- * The default if PCI isn't enabled, or if no PCI clk setting is given
- * is 66MHz; this is what the board defaults to when the PCI slot is
- * physically empty. The board will automatically (i.e w/o jumpers)
- * clock down to 33MHz if you insert a 33MHz PCI card.
- */
-#ifdef CONFIG_PCI_33M
-#define CONFIG_83XX_CLKIN 33000000 /* in Hz */
-#else /* 66M */
-#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
-#endif
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#ifdef CONFIG_PCI_33M
-#define CONFIG_SYS_CLK_FREQ 33000000
-#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1
-#else /* 66M */
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
-#endif
-#endif
-
#define CONFIG_SYS_IMMR 0xE0000000
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
/*
* FLASH on the Local Bus
*/
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* start of FLASH */
#define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */
-/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
- | BR_PS_16 /* 16 bit port */ \
- | BR_MS_GPCM /* MSEL = GPCM */ \
- | BR_V) /* valid */
-
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
- | OR_GPCM_XAM \
- | OR_GPCM_CSNT \
- | OR_GPCM_ACS_DIV2 \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
- /* 0xFF806FF7 */
-
- /* window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
+
+/* FLASH */
+#define CONFIG_SYS_BR0_PRELIM (0xFF800000 | BR_PS_16 | BR_MS_GPCM | BR_V)
+#define CONFIG_SYS_OR0_PRELIM (OR_AM_8MB | OR_GPCM_XAM | OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS | OR_GPCM_SCY_15 | OR_GPCM_TRLX_SET | OR_GPCM_EHTR_SET | OR_GPCM_EAD)
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */
| BR_MS_SDRAM \
| BR_V)
/* 0xF0001861 */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB)
-
/*
* The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
*
* 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
*/
-#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_LBC_SDRAM_SIZE) \
+#define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB \
| OR_SDRAM_XAM \
| ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \
| ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \
/*
* Serial Port
*/
-#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#if defined(CONFIG_PCI)
-#define PCI_64BIT
-#define PCI_ONE_PCI1
-#if defined(PCI_64BIT)
-#undef PCI_ALL_PCI1
-#undef PCI_TWO_PCI1
-#undef PCI_ONE_PCI1
-#endif
-
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
/*
* TSEC configuration
*/
-#define CONFIG_TSEC_ENET /* TSEC ethernet support */
#if defined(CONFIG_TSEC_ENET)
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
- /* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
- /* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
-#if 1 /*528/264*/
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN |\
- HRCWL_VCO_1X2 |\
- HRCWL_CORE_TO_CSB_2X1)
-#elif 0 /*396/132*/
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN |\
- HRCWL_VCO_1X4 |\
- HRCWL_CORE_TO_CSB_3X1)
-#elif 0 /*264/132*/
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN |\
- HRCWL_VCO_1X4 |\
- HRCWL_CORE_TO_CSB_2X1)
-#elif 0 /*132/132*/
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN |\
- HRCWL_VCO_1X4 |\
- HRCWL_CORE_TO_CSB_1X1)
-#elif 0 /*264/264 */
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN |\
- HRCWL_VCO_1X4 |\
- HRCWL_CORE_TO_CSB_1X1)
-#endif
-
-#if defined(PCI_64BIT)
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_PCI_HOST |\
- HRCWH_64_BIT_PCI |\
- HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_PCI2_ARBITER_DISABLE |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0X00000100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT |\
- HRCWH_TSEC1M_IN_GMII |\
- HRCWH_TSEC2M_IN_GMII)
-#else
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_PCI_HOST |\
- HRCWH_32_BIT_PCI |\
- HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_PCI2_ARBITER_ENABLE |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0X00000100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT |\
- HRCWH_TSEC1M_IN_GMII |\
- HRCWH_TSEC2M_IN_GMII)
-#endif
-
/* System IO Config */
#define CONFIG_SYS_SICRH 0
#define CONFIG_SYS_SICRL SICRL_LDP_A
#define CONFIG_SYS_HID2 HID2_HBE
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/* DDR @ 0x00000000 */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-/* PCI @ 0x80000000 */
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#else
-#define CONFIG_SYS_IBAT1L (0)
-#define CONFIG_SYS_IBAT1U (0)
-#define CONFIG_SYS_IBAT2L (0)
-#define CONFIG_SYS_IBAT2U (0)
-#endif
-
-#ifdef CONFIG_MPC83XX_PCI2
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#else
-#define CONFIG_SYS_IBAT3L (0)
-#define CONFIG_SYS_IBAT3U (0)
-#define CONFIG_SYS_IBAT4L (0)
-#define CONFIG_SYS_IBAT4U (0)
#endif
-/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-/* LBC SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L (CONFIG_SYS_LBC_SDRAM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U (CONFIG_SYS_LBC_SDRAM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-#define CONFIG_SYS_IBAT7L (0)
-#define CONFIG_SYS_IBAT7U (0)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#endif
#define CONFIG_HAS_ETH1
#endif
-#define CONFIG_HOSTNAME SBC8349
+#define CONFIG_HOSTNAME "SBC8349"
#define CONFIG_ROOTPATH "/tftpboot/rootfs"
#define CONFIG_BOOTFILE "uImage"
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 800000
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=sbc8349\0" \
projects / oweals / u-boot.git / blobdiff