#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * If we are developing, we might want to start armboot from ram
- * so we MUST NOT initialize critical regs like mem-timing ...
- */
-#define CONFIG_INIT_CRITICAL
-
/*
* High Level Configuration Options
* (easy to change)
#define CONFIG_OMAP1610 1 /* 5912 is same as 1610 */
#define CONFIG_OSK_OMAP5912 1 /* a OSK Board */
+#define CONFIG_DISPLAY_CPUINFO 1 /* display cpu info (and speed) */
+#define CONFIG_DISPLAY_BOARDINFO 1 /* display board info */
+
/* input clock of PLL */
/* the OMAP5912 OSK has 12MHz input clock */
#define CONFIG_SYS_CLK_FREQ 12000000
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1 /* Required for ramdisk support */
/*
* Size of malloc() pool
*/
#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/*
* Hardware drivers
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP)
-#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+
+
#include <configs/omap1510.h>
#define CONFIG_BOOTDELAY 3
#define CONFIG_SERVERIP 156.117.97.139 /* current IP of my dev pc */
#define CONFIG_BOOTFILE "uImage" /* file to load */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
#endif
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */
#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */
-#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
+#define PHYS_FLASH_2 0x01000000 /* Flash Bank #2 */
+
+#define CFG_FLASH_BASE PHYS_FLASH_1
-#define CFG_FLASH_BASE PHYS_FLASH_1
+#define CFG_MONITOR_BASE CFG_FLASH_BASE /* Monitor at beginning of flash */
/*-----------------------------------------------------------------------
- * FLASH and environment organization
+ * FLASH driver setup
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */
+
+#define CFG_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 }
+
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define PHYS_FLASH_SIZE 0x02000000 /* 32MB */
#define CFG_MAX_FLASH_SECT (259) /* max number of sectors on one chip */
-/* addr of environment */
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x020000)
+
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
+#define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */
+
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
/* timeout values are in ticks */
#define CFG_FLASH_ERASE_TOUT (20*CFG_HZ) /* Timeout for Flash Erase */
#define CFG_FLASH_WRITE_TOUT (20*CFG_HZ) /* Timeout for Flash Write */
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
#define CFG_ENV_IS_IN_FLASH 1
+/* addr of environment */
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x020000)
+
#define CFG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */
#define CFG_ENV_OFFSET 0x20000 /* environment starts here */