/*
* High Level Configuration Options
*/
-#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
#define CONFIG_OMAP 1 /* in a TI OMAP core */
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
#define CONFIG_OMAP3430 1 /* which is in a 3430 */
#define CONFIG_OMAP3_ZOOM2 1 /* working with Zoom II */
+#define CONFIG_SDRC /* The chip has SDRC controller */
+
#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap3.h>
#define CONFIG_INITRD_TAG 1
#define CONFIG_REVISION_TAG 1
+#define CONFIG_OF_LIBFDT 1
+
/*
* Size of malloc() pool
*/
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
- /* initial data */
/*
* Hardware drivers
*/
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
+#define CONFIG_GENERIC_MMC 1
#define CONFIG_MMC 1
-#define CONFIG_OMAP3_MMC 1
+#define CONFIG_OMAP_HSMMC 1
#define CONFIG_DOS_PARTITION 1
/* DDR - I use Micron DDR */
#define CONFIG_EXTRA_ENV_SETTINGS \
"usbtty=cdc_acm\0" \
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_PROMPT "OMAP3 Zoom2 # "
#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_CBSIZE 512
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
- /* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-#define CONFIG_SYS_FLASH_BASE boot_flash_base
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
+#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_ENV_IS_IN_NAND 1
#define SMNAND_ENV_OFFSET 0x0c0000 /* environment starts here */
-#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
-#define CONFIG_ENV_OFFSET boot_flash_off
+#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-#ifndef __ASSEMBLY__
-extern unsigned int boot_flash_base;
-extern volatile unsigned int boot_flash_env_addr;
-extern unsigned int boot_flash_off;
-extern unsigned int boot_flash_sec;
-extern unsigned int boot_flash_type;
-#endif
-
#endif /* __CONFIG_H */