#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap3.h>
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO 1
+#define CONFIG_DISPLAY_BOARDINFO 1
+
/* Clock Defines */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
/*
* NS16550 Configuration
+ * Zoom2 uses the TL16CP754C on the debug board
+ */
+#define CONFIG_SERIAL_MULTI 1
+/*
+ * 0 - 1 : first USB with respect to the left edge of the debug board
+ * 2 - 3 : second USB with respect to the left edge of the debug board
*/
-#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
+#define ZOOM2_DEFAULT_SERIAL_DEVICE (&zoom2_serial_device0)
+
+#define V_NS16550_CLK (1843200) /* 1.8432 Mhz */
#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_REG_SIZE (-2)
#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
-
-/*
- * select serial console configuration
- */
-#define CONFIG_CONS_INDEX 3
-#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
-#define CONFIG_SERIAL3 3 /* UART3 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {115200}
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
- 115200}
+
#define CONFIG_MMC 1
#define CONFIG_OMAP3_MMC 1
#define CONFIG_DOS_PARTITION 1
+/* Status LED */
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+#define CONFIG_BOARD_SPECIFIC_LED 1
+#define STATUS_LED_BLUE 0
+#define STATUS_LED_RED 1
+/* Blue */
+#define STATUS_LED_BIT STATUS_LED_BLUE
+#define STATUS_LED_STATE STATUS_LED_ON
+#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+/* Red */
+#define STATUS_LED_BIT1 STATUS_LED_RED
+#define STATUS_LED_STATE1 STATUS_LED_OFF
+#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
+/* Optional value */
+#define STATUS_LED_BOOT STATUS_LED_BIT
+
+/* GPIO banks */
+#ifdef CONFIG_STATUS_LED
+#define CONFIG_OMAP3_GPIO_2 /* ZOOM2_LED_BLUE2 */
+#define CONFIG_OMAP3_GPIO_6 /* ZOOM2_LED_RED */
+#endif
+#define CONFIG_OMAP3_GPIO_3 /* board revision */
+#define CONFIG_OMAP3_GPIO_5 /* debug board detection, ZOOM2_LED_BLUE */
+
/* commands to include */
#include <config_cmd_default.h>
#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
+
/* Environment information */
#define CONFIG_BOOTDELAY 10