#include <configs/ti_omap3_common.h>
+#ifdef CONFIG_SPL_BUILD
+/*
+ * Disable MMC DM for SPL build and can be re-enabled after adding
+ * DM support in SPL
+ */
+#undef CONFIG_DM_MMC
+#undef OMAP_HSMMC_USE_GPIO
+
+/* select serial console configuration for SPL */
+#undef CONFIG_CONS_INDEX
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
+#endif
+
+
/*
* We are only ever GP parts and will utilize all of the "downloaded image"
* area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in
* order to allow for BCH8 to fit in.
*/
#undef CONFIG_SPL_TEXT_BASE
+#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x40200000
-#define CONFIG_BOARD_LATE_INIT
#define CONFIG_MISC_INIT_R /* misc_init_r dumps the die id */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
/* Hardware drivers */
-/* GPIO banks */
-#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
-
#define CONFIG_USB_OMAP3
-/* select serial console configuration */
-#undef CONFIG_CONS_INDEX
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
-#define CONFIG_SERIAL1 1 /* UART1 on OMAP Logic boards */
-
-/* commands to include */
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_CMD_NAND_LOCK_UNLOCK /* nand (un)lock commands */
-
/* I2C */
-#define CONFIG_SYS_I2C_OMAP34XX
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */
-#define EXPANSION_EEPROM_I2C_BUS 2 /* I2C Bus for AT24C64 */
-#define CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID
/* USB */
#define CONFIG_USB_MUSB_OMAP2PLUS
#define CONFIG_USB_MUSB_PIO_ONLY
-#define CONFIG_USB_ETHER
-#define CONFIG_USB_ETHER_RNDIS
-#define CONFIG_USB_FUNCTION_FASTBOOT
-#define CONFIG_CMD_FASTBOOT
-#define CONFIG_ANDROID_BOOT_IMAGE
-#define CONFIG_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR
-#define CONFIG_FASTBOOT_BUF_SIZE 0x07000000
/* TWL4030 */
-#define CONFIG_TWL4030_PWM
#define CONFIG_TWL4030_USB
/* Board NAND Info. */
#ifdef CONFIG_NAND
#define CONFIG_NAND_OMAP_GPMC
-#define CONFIG_CMD_UBIFS /* Read-only UBI volume operations */
-#define CONFIG_RBTREE /* required by CONFIG_CMD_UBI */
-#define CONFIG_LZO /* required by CONFIG_CMD_UBIFS */
-
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 13
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
-#define CONFIG_BCH
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_ENV_IS_IN_NAND 1
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
-#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
-#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+#define CONFIG_ENV_OFFSET 0x260000
+#define CONFIG_ENV_ADDR 0x260000
/* SMSC922x Ethernet */
#if defined(CONFIG_CMD_NET)
/* Defines for SPL */
-#define CONFIG_SPL_OMAP3_ID_NAND
-
/* NAND: SPL falcon mode configs */
#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_CMD_SPL_NAND_OFS 0x240000
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
-#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
#endif
#endif /* __CONFIG_H */