#define CONFIG_MISC_INIT_R
#define CONFIG_OF_LIBFDT 1
-/*
- * The early kernel mapping on ARM currently only maps from the base of DRAM
- * to the end of the kernel image. The kernel is loaded at DRAM base + 0x8000.
- * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000,
- * so that leaves DRAM base to DRAM base + 0x4000 available.
- */
-#define CONFIG_SYS_BOOTMAPSZ 0x4000
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
- /* initial data */
/*
* Hardware drivers
#define CONFIG_OMAP_HSMMC 1
#define CONFIG_DOS_PARTITION 1
+/* Status LED */
+#define CONFIG_STATUS_LED 1
+#define CONFIG_BOARD_SPECIFIC_LED 1
+#define STATUS_LED_BIT 0x01
+#define STATUS_LED_STATE STATUS_LED_ON
+#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BIT1 0x02
+#define STATUS_LED_STATE1 STATUS_LED_ON
+#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BOOT STATUS_LED_BIT
+#define STATUS_LED_GREEN STATUS_LED_BIT1
+
/* DDR - I use Micron DDR */
#define CONFIG_OMAP3_MICRON_DDR 1
#define CONFIG_USB_TTY 1
#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+/* USB EHCI */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
+
/* commands to include */
#include <config_cmd_default.h>
#define CONFIG_CMD_I2C /* I2C serial bus support */
#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_USB_STORAGE /* USB storage support */
#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_LED /* LED support */
#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
"loadaddr=0x82000000\0" \
"usbtty=cdc_acm\0" \
"console=ttyS2,115200n8\0" \
- "mpurate=500\0" \
+ "mpurate=auto\0" \
"vram=12M\0" \
"dvimode=1024x768MR-16@60\0" \
"defaultdisplay=dvi\0" \
"omapdss.def_disp=${defaultdisplay} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
- "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source ${loadaddr}\0" \
+ "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \
+ "importbootenv=echo Importing environment from mmc ...; " \
+ "env import -t $loadaddr $filesize\0" \
"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
#define CONFIG_BOOTCOMMAND \
"if mmc rescan ${mmcdev}; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loaduimage; then " \
- "run mmcboot; " \
- "else run nandboot; " \
- "fi; " \
- "fi; " \
- "else run nandboot; fi"
+ "echo SD/MMC found on device ${mmcdev};" \
+ "if run loadbootenv; then " \
+ "run importbootenv;" \
+ "fi;" \
+ "if test -n $uenvcmd; then " \
+ "echo Running uenvcmd ...;" \
+ "run uenvcmd;" \
+ "fi;" \
+ "if run loaduimage; then " \
+ "run mmcboot;" \
+ "fi;" \
+ "fi;" \
+ "run nandboot;" \
#define CONFIG_AUTO_COMPLETE 1
/*
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
- /* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-#define CONFIG_SYS_FLASH_BASE boot_flash_base
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
+#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
-#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
-#define CONFIG_ENV_OFFSET boot_flash_off
+#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
- CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-
-#ifndef __ASSEMBLY__
-extern unsigned int boot_flash_base;
-extern volatile unsigned int boot_flash_env_addr;
-extern unsigned int boot_flash_off;
-extern unsigned int boot_flash_sec;
-extern unsigned int boot_flash_type;
-#endif
-
-/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+
+#define CONFIG_OMAP3_SPI
#endif /* __CONFIG_H */