#define CONFIG_OMAP 1 /* in a TI OMAP core */
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
#define CONFIG_OMAP3_BEAGLE 1 /* working with BEAGLE */
+#define CONFIG_OMAP_GPIO
#define CONFIG_SDRC /* The chip has SDRC controller */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
-#undef CONFIG_USE_IRQ /* no support for IRQs */
#define CONFIG_MISC_INIT_R
#define CONFIG_OF_LIBFDT 1
#define CONFIG_CMD_USB
#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_OMAP
+/*#define CONFIG_EHCI_DCACHE*/ /* leave it disabled for now */
+#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
+
#define CONFIG_USB_ULPI
#define CONFIG_USB_ULPI_VIEWPORT_OMAP
/* commands to include */
#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_EXT2 /* EXT2 Support */
#define CONFIG_CMD_FAT /* FAT support */
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_SETEXPR /* Evaluate expressions */
+#define CONFIG_CMD_GPIO /* Enable gpio command */
#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
/* partition */
/* Environment information */
-#define CONFIG_BOOTDELAY 2
+#define CONFIG_BOOTDELAY 3
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x80200000\0" \
"bootfile=uImage.beagle\0" \
"console=ttyO2,115200n8\0" \
"mpurate=auto\0" \
- "buddy=none "\
+ "buddy=none\0" \
"optargs=\0" \
"camera=none\0" \
"vram=12M\0" \
"ramboot=echo Booting from ramdisk ...; " \
"run ramargs; " \
"bootm ${loadaddr}\0" \
-
+ "userbutton=if gpio input 173; then run userbutton_xm; " \
+ "else run userbutton_nonxm; fi;\0" \
+ "userbutton_xm=gpio input 4;\0" \
+ "userbutton_nonxm=gpio input 7;\0"
+/* "run userbutton" will return 1 (false) if is pressed and 0 (false) if not */
#define CONFIG_BOOTCOMMAND \
- "if mmc rescan ${mmcdev}; then " \
- "if userbutton; then " \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run userbutton; then " \
+ "setenv bootenv uEnv.txt;" \
+ "else " \
"setenv bootenv user.txt;" \
"fi;" \
"echo SD/MMC found on device ${mmcdev};" \
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_PROMPT "OMAP3 beagleboard.org # "
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
#define CONFIG_SYS_HZ 1000
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
-
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
/* Defines for SPL */
#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_NAND_SIMPLE
#define CONFIG_SPL_TEXT_BASE 0x40200800
-#define CONFIG_SPL_MAX_SIZE (45 * 1024)
+#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_POWER_SUPPORT
#define CONFIG_SPL_OMAP3_ID_NAND
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"