/*#define CONFIG_APTIX 1 #* define if on APTIX test chip */
/*#define CONFIG_VIRTIO 1 #* Using Virtio simulator */
-#define PRCM_CONFIG_II 1
-#define CONFIG_PARTIAL_SRAM 1
+/* Clock config to target*/
+#define PRCM_CONFIG_II 1
+/* #define PRCM_CONFIG_III 1 */
#include <asm/arch/omap2420.h> /* get chip and board defs */
+/* On H4, NOR and NAND flash are mutual exclusive.
+ Define this if you want to use NAND
+ */
+/*#define CFG_NAND_BOOT */
+
#ifdef CONFIG_APTIX
#define V_SCLK 1500000
#else
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG 1
+#define CONFIG_REVISION_TAG 1
/*
* Size of malloc() pool
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP | CFG_CMD_I2C)
-/* I'd like to get to these. Snap kernel loads if we make MMC go */
- /* #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_NAND | CFG_CMD_JFFS2 | CFG_CMD_DHCP | CFG_CMD_MMC | CFG_CMD_FAT | CFG_CMD_I2C) */
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#ifdef CFG_NAND_BOOT
+ #define CONFIG_CMD_DHCP
+ #define CONFIG_CMD_I2C
+ #define CONFIG_CMD_NAND
+ #define CONFIG_CMD_JFFS2
+#else
+ #define CONFIG_CMD_DHCP
+ #define CONFIG_CMD_I2C
+ #define CONFIG_CMD_JFFS2
+
+ #undef CONFIG_CMD_AUTOSCRIPT
+#endif
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_NAND_LEGACY
+#define CFG_NAND_ADDR 0x04000000 /* physical address to access nand at CS0*/
+
+#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define SECTORSIZE 512
-#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define WRITE_NAND_COMMAND(d, adr) do {*(volatile u16 *)0x6800A07C = d;} while(0)
+#define WRITE_NAND_ADDRESS(d, adr) do {*(volatile u16 *)0x6800A080 = d;} while(0)
+#define WRITE_NAND(d, adr) do {*(volatile u16 *)0x6800A084 = d;} while(0)
+#define READ_NAND(adr) (*(volatile u16 *)0x6800A084)
+#define NAND_WAIT_READY(nand) udelay(10)
+
+#define NAND_NO_RB 1
+
+#define CFG_NAND_WP
+#define NAND_WP_OFF() do {*(volatile u32 *)(0x6800A050) |= 0x00000010;} while(0)
+#define NAND_WP_ON() do {*(volatile u32 *)(0x6800A050) &= ~0x00000010;} while(0)
+
+#define NAND_CTL_CLRALE(nandptr)
+#define NAND_CTL_SETALE(nandptr)
+#define NAND_CTL_CLRCLE(nandptr)
+#define NAND_CTL_SETCLE(nandptr)
+#define NAND_DISABLE_CE(nand)
+#define NAND_ENABLE_CE(nand)
#define CONFIG_BOOTDELAY 3
#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
#define PHYS_SDRAM_2 OMAP2420_SDRC_CS1
+#define PHYS_FLASH_SECT_SIZE SZ_128K
#define PHYS_FLASH_1 H4_CS0_BASE /* Flash Bank #1 */
#define PHYS_FLASH_SIZE_1 SZ_32M
#define PHYS_FLASH_2 (H4_CS0_BASE+SZ_32M) /* same cs, 2 chips in series */
#define PHYS_FLASH_SIZE_2 SZ_32M
-#define CFG_FLASH_BASE PHYS_FLASH_1
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
+#define CFG_FLASH_BASE PHYS_FLASH_1
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT (259) /* max number of sectors on one chip */
+#define CFG_MONITOR_BASE CFG_FLASH_BASE /* Monitor at beginning of flash */
+#define CFG_MONITOR_LEN SZ_128K /* Reserve 1 sector */
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, CFG_FLASH_BASE + PHYS_FLASH_SIZE_1 }
+#ifdef CFG_NAND_BOOT
+#define CFG_ENV_IS_IN_NAND 1
+#define CFG_ENV_OFFSET 0x80000 /* environment starts here */
+#else
#define CFG_ENV_ADDR (CFG_FLASH_BASE + SZ_128K)
#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE
+#define CFG_ENV_OFFSET ( CFG_MONITOR_BASE + CFG_MONITOR_LEN ) /* Environment after Monitor */
+#endif
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+#define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
+#define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (10*75*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (10*75*CFG_HZ) /* Timeout for Flash Write */
+#define CFG_FLASH_ERASE_TOUT (100*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT (100*CFG_HZ) /* Timeout for Flash Write */
+
+#define CFG_JFFS2_MEM_NAND
+
+/*
+ * JFFS2 partitions
+ */
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor1"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor1=omap2420-1"
+#define MTDPARTS_DEFAULT "mtdparts=omap2420-1:-(jffs2)"
+*/
#endif /* __CONFIG_H */