/*#define CONFIG_VIRTIO 1 #* Using Virtio simulator */
/* Clock config to target*/
-#define PRCM_CONFIG_II 1
-/*#define PRCM_CONFIG_III 1 */
-
-/* Memory configuration on board */
-/*#define CONFIG_OPTIMIZE_DDR 1 */
+#define PRCM_CONFIG_II 1
+/* #define PRCM_CONFIG_III 1 */
#include <asm/arch/omap2420.h> /* get chip and board defs */
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
#ifdef CFG_NAND_BOOT
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP | CFG_CMD_I2C | CFG_CMD_NAND | CFG_CMD_JFFS2)
+ #define CONFIG_CMD_DHCP
+ #define CONFIG_CMD_I2C
+ #define CONFIG_CMD_NAND
+ #define CONFIG_CMD_JFFS2
#else
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP | CFG_CMD_I2C | CFG_CMD_JFFS2)
+ #define CONFIG_CMD_DHCP
+ #define CONFIG_CMD_I2C
+ #define CONFIG_CMD_JFFS2
+
+ #undef CONFIG_CMD_AUTOSCRIPT
#endif
-/* I'd like to get to these. Snap kernel loads if we make MMC go */
- /* #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_NAND | CFG_CMD_JFFS2 | CFG_CMD_DHCP | CFG_CMD_MMC | CFG_CMD_FAT | CFG_CMD_I2C) */
-#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+
/*
* Board NAND Info.
*/
+#define CONFIG_NAND_LEGACY
#define CFG_NAND_ADDR 0x04000000 /* physical address to access nand at CS0*/
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_WP_OFF() do {*(volatile u32 *)(0x6800A050) |= 0x00000010;} while(0)
#define NAND_WP_ON() do {*(volatile u32 *)(0x6800A050) &= ~0x00000010;} while(0)
-
#define NAND_CTL_CLRALE(nandptr)
#define NAND_CTL_SETALE(nandptr)
#define NAND_CTL_CLRCLE(nandptr)
#define NAND_DISABLE_CE(nand)
#define NAND_ENABLE_CE(nand)
-
#define CONFIG_BOOTDELAY 3
#ifdef NFS_BOOT_DEFAULTS
#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
#define PHYS_SDRAM_2 OMAP2420_SDRC_CS1
+#define PHYS_FLASH_SECT_SIZE SZ_128K
#define PHYS_FLASH_1 H4_CS0_BASE /* Flash Bank #1 */
#define PHYS_FLASH_SIZE_1 SZ_32M
#define PHYS_FLASH_2 (H4_CS0_BASE+SZ_32M) /* same cs, 2 chips in series */
#define PHYS_FLASH_SIZE_2 SZ_32M
-#define CFG_FLASH_BASE PHYS_FLASH_1
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
+#define CFG_FLASH_BASE PHYS_FLASH_1
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT (259) /* max number of sectors on one chip */
+#define CFG_MONITOR_BASE CFG_FLASH_BASE /* Monitor at beginning of flash */
+#define CFG_MONITOR_LEN SZ_128K /* Reserve 1 sector */
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, CFG_FLASH_BASE + PHYS_FLASH_SIZE_1 }
#ifdef CFG_NAND_BOOT
#define CFG_ENV_IS_IN_NAND 1
#else
#define CFG_ENV_ADDR (CFG_FLASH_BASE + SZ_128K)
#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE
+#define CFG_ENV_OFFSET ( CFG_MONITOR_BASE + CFG_MONITOR_LEN ) /* Environment after Monitor */
#endif
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+#define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
+#define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */
+
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (30*75*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (30*75*CFG_HZ) /* Timeout for Flash Write */
+#define CFG_FLASH_ERASE_TOUT (100*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT (100*CFG_HZ) /* Timeout for Flash Write */
-/* Flash banks JFFS2 should use */
-#define CFG_MAX_MTD_BANKS (CFG_MAX_FLASH_BANKS+CFG_MAX_NAND_DEVICE)
#define CFG_JFFS2_MEM_NAND
-#define CFG_JFFS2_FIRST_BANK 1 /* use flash_info[1] */
-#define CFG_JFFS2_NUM_BANKS 1
+
+/*
+ * JFFS2 partitions
+ */
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor1"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor1=omap2420-1"
+#define MTDPARTS_DEFAULT "mtdparts=omap2420-1:-(jffs2)"
+*/
#endif /* __CONFIG_H */