/* On H4, NOR and NAND flash are mutual exclusive.
Define this if you want to use NAND
*/
-/*#define CFG_NAND_BOOT */
+/*#define CONFIG_SYS_NAND_BOOT */
#ifdef CONFIG_APTIX
#define V_SCLK 1500000
/*
* Size of malloc() pool
*/
-#define CFG_ENV_SIZE SZ_128K /* Total Size of Environment Sector */
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + SZ_128K)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_ENV_SIZE SZ_128K /* Total Size of Environment Sector */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/*
* Hardware drivers
#define V_NS16550_CLK (48000000) /* 48MHz (APLL96/2) */
#endif
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE (-4)
-#define CFG_NS16550_CLK V_NS16550_CLK /* 3MHz (1.5MHz*2) */
-#define CFG_NS16550_COM1 OMAP2420_UART1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK /* 3MHz (1.5MHz*2) */
+#define CONFIG_SYS_NS16550_COM1 OMAP2420_UART1
/*
* select serial console configuration
* I2C configuration
*/
#define CONFIG_HARD_I2C
-#define CFG_I2C_SPEED 100000
-#define CFG_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 1
#define CONFIG_DRIVER_OMAP24XX_I2C
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CFG_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
+#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/*
*/
#include <config_cmd_default.h>
-#ifdef CFG_NAND_BOOT
+#ifdef CONFIG_SYS_NAND_BOOT
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_I2C
#define CONFIG_CMD_NAND
/*
* Board NAND Info.
*/
-#define CFG_NAND_LEGACY
-#define CFG_NAND_ADDR 0x04000000 /* physical address to access nand at CS0*/
+#define CONFIG_NAND_LEGACY
+#define CONFIG_SYS_NAND_ADDR 0x04000000 /* physical address to access nand at CS0*/
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define ADDR_COLUMN 1
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
#define WRITE_NAND_COMMAND(d, adr) do {*(volatile u16 *)0x6800A07C = d;} while(0)
#define WRITE_NAND_ADDRESS(d, adr) do {*(volatile u16 *)0x6800A080 = d;} while(0)
#define NAND_NO_RB 1
-#define CFG_NAND_WP
+#define CONFIG_SYS_NAND_WP
#define NAND_WP_OFF() do {*(volatile u32 *)(0x6800A050) |= 0x00000010;} while(0)
#define NAND_WP_ON() do {*(volatile u32 *)(0x6800A050) &= ~0x00000010;} while(0)
#define V_PROMPT "OMAP242x H4 # "
#endif
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT V_PROMPT
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT V_PROMPT
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START (OMAP2420_SDRC_CS0) /* memtest works on */
-#define CFG_MEMTEST_END (OMAP2420_SDRC_CS0+SZ_31M)
+#define CONFIG_SYS_MEMTEST_START (OMAP2420_SDRC_CS0) /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END (OMAP2420_SDRC_CS0+SZ_31M)
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
-
-#define CFG_LOAD_ADDR (OMAP2420_SDRC_CS0) /* default load address */
+#define CONFIG_SYS_LOAD_ADDR (OMAP2420_SDRC_CS0) /* default load address */
/* The 2420 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
* 32KHz clk, or from external sig. This rate is divided by a local divisor.
*/
#ifdef CONFIG_APTIX
-#define V_PVT 3
+#define V_PTV 3
#else
-#define V_PVT 7 /* use with 12MHz/128 */
+#define V_PTV 7 /* use with 12MHz/128 */
#endif
-#define CFG_TIMERBASE OMAP2420_GPT2
-#define CFG_PVT V_PVT /* 2^(pvt+1) */
-#define CFG_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CFG_PVT))
+#define CONFIG_SYS_TIMERBASE OMAP2420_GPT2
+#define CONFIG_SYS_PTV V_PTV /* 2^(PTV+1) */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_FLASH_BASE PHYS_FLASH_1
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT (259) /* max number of sectors on one chip */
-#define CFG_MONITOR_BASE CFG_FLASH_BASE /* Monitor at beginning of flash */
-#define CFG_MONITOR_LEN SZ_128K /* Reserve 1 sector */
-#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, CFG_FLASH_BASE + PHYS_FLASH_SIZE_1 }
-
-#ifdef CFG_NAND_BOOT
-#define CFG_ENV_IS_IN_NAND 1
-#define CFG_ENV_OFFSET 0x80000 /* environment starts here */
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT (259) /* max number of sectors on one chip */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */
+#define CONFIG_SYS_MONITOR_LEN SZ_128K /* Reserve 1 sector */
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + PHYS_FLASH_SIZE_1 }
+
+#ifdef CONFIG_SYS_NAND_BOOT
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_OFFSET 0x80000 /* environment starts here */
#else
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + SZ_128K)
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE
-#define CFG_ENV_OFFSET ( CFG_MONITOR_BASE + CFG_MONITOR_LEN ) /* Environment after Monitor */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + SZ_128K)
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE
+#define CONFIG_ENV_OFFSET ( CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN ) /* Environment after Monitor */
#endif
/*-----------------------------------------------------------------------
* CFI FLASH driver setup
*/
-#define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */
-#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
-#define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (100*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (100*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (100*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (100*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-#define CFG_JFFS2_MEM_NAND
+#define CONFIG_SYS_JFFS2_MEM_NAND
/*
* JFFS2 partitions
*/
/* No command line, one static partition, whole device */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor1"
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
/*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nor1=omap2420-1"
#define MTDPARTS_DEFAULT "mtdparts=omap2420-1:-(jffs2)"
*/